CSA/ANSI Z21.20:22 • CSA C22.2 No. 60730-2-5:22

Scope Replacement: This part of IEC 60730 applies to automatic electrical BURNER CONTROL SYSTEMS for the AUTOMATIC CONTROL of burners for oil, gas, coal or other combustibles intended to be used • for household and similar use, • in shops, offices, hospitals, farms and commercial and industrial applications. This International Standard is applicable • to a complete BURNER CONTROL SYSTEM, • to a separate PROGRAMMING UNIT, • to a separate electronic high-voltage IGNITION SOURCE, • to a separate FLAME DETECTOR and • to a separate HIGH-TEMPERATURE OPERATION (HTO) DETECTOR. • to a BURNER CONTROL SYSTEM intended to be used in warm air heating appliances (furnaces) where the appliance is equipped with an electromechanical differential pressure control to monitor the difference of the combustion air pressure (Type 2.AL). This pressure control provides a switch as an alternative to one of the two switching elements to directly de-energize the safety relevant terminals. NOTE 1 Throughout this document, where it can be used unambiguously, the word "system" means "burner control system" and "systems" means "burner control systems". NOTE 2 Throughout this document, the word "equipment" means "appliance and equipment." This standard does not apply to thermoelectric flame supervision controls; thermoelectric flame supervision controls are covered by ISO 23551-6. This document also applies to electrical BURNER CONTROL SYSTEMS intended exclusively for industrial process applications e.g. those applications covered by ISO TC 244 (ISO 13577). This document applies to controls powered by primary or secondary batteries, requirements for which are contained within the standard, including Annex V. 1.1DV.1 D2 Modification of 1.1 of the Part 2 by adding the following: Components of burner control systems such as electrodes, flame supervision, oxygen depletion safety shut-off systems (ODS), thermoelectric safety shut-off devices, pilot burners, thermocouples, fast-acting thermocouples, and other components are covered by this Part 2-5. (Refer to Annex DVKK.) 1.1DV.2 D2 Modification of 1.1 of the Part 2 by adding the following note: NOTE 3DV Requirements for separate ignition transformers are covered in UL 506 and CSA C22.2 No. 13. 1.1DV.3 DE Modification of 1.1 of the Part 2 by adding the following: In Canada, this Standard applies to equipment that is intended to be installed or used in accordance with CSA C22.1, Canadian Electrical Code, Part I. In Canada, general requirements applicable to these products are provided in CSA C22.2 No. 0. 1.1.1 This document applies to the inherent safety, to the declared OPERATING VALUES, OPERATING TIMES and OPERATING SEQUENCES where such are associated with burner safety and to the testing of automatic electrical BURNER CONTROL SYSTEMS used in, on, or in association with, burners. NOTE Requirements for specific OPERATING VALUES, OPERATING TIMES and OPERATING SEQUENCES are given in the standards for appliances and equipment. 1.1.2 This document applies to AC or DC powered systems with a rated voltage not exceeding 660 V AC or 600 V DC. 1.1.3 This document does not take into account the RESPONSE VALUE of an AUTOMATIC ACTION of a CONTROL, if such a RESPONSE VALUE is dependent upon the method of mounting the control in the equipment. Where a RESPONSE VALUE is of significant purpose for the protection of the user, or surroundings, the value defined in the appropriate equipment standard or as determined by the manufacturer applies. 1.1.4 This document applies also to systems incorporating ELECTRONIC DEVICES, requirements for which are contained in Annex H. 1.1.4DV D2 Modification of 1.1.4 of the Part 2 by adding the following: This Standard also applies to manufacturing and production testing (see Annex DVLL) and solid-state oil igniters (see Annex DVMM). 1.1.5 This document applies to systems using NTC or PTC thermistors, additional requirements for which are contained in Annex J. 1.1.6 This document includes systems responsive to flame properties and temperature for HTO. 1.1.7 This document applies to the electrical and functional safety of controls capable of receiving and responding to communications signals. The signals may be transmitted to or received from external units, connected wired or wireless, that may or may not be part of the burner control system. 1.1.8 This document does not address the integrity of the output signal to the network devices, such as interoperability with other devices, unless it has been evaluated as part of the control system. 1.2 Normative references This clause of Part 1 is applicable except as follows: Addition: IEC 60068-2-6, Environmental testing – Part 2: Tests – Test Fc: Vibration (sinusoidal) IEC 60079-20-1:2010, Explosive atmospheres – Part 20-1: Material characteristics for gas and vapour classification – Test methods and data ISO 23551-6:2014, Safety and control devices for gas burners and gas-burning appliances – Particular requirements – Part 6: Thermoelectric flame supervision controls Replacement: IEC 60127-1:2015, Miniature fuses – Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links 1.2DV DC Modification by adding the following to 1.2 of the Part 2: ANSI/ASME B1.20.1-2013 (R2018), Pipe Threads, General Purpose (Inch) CSA/ANSI Z21.21:19/CSA 6.5:19, Automatic valves for gas appliances ANSI Z21.78-2010 (R2020)/CSA 6.20-2010 (R2020), Combination gas controls for gas appliances CSA B140.2.1-10 (R2019), Atomizing-type oil burners CAN/CSA-C22.2 No. 0.17-00 (R2018), Evaluation of properties of polymeric materials CSA C22.2 No. 13-13 (R2018), Transformers for oil- or gas-burner ignition equipment CSA C22.2 No. 269.2-17, Surge protective devices – Type 2 – Permanently connected CSA E60730-1:15 (R2020), Automatic electrical controls – Part 1: General requirements UL 506-2017, Specialty Transformers UL 1449-2021, Surge Protective Devices UL 60730-1, Automatic Electrical Controls – Part 1: General Requirements Government of Canada, ICES-003, 2020, Information Technology Equipment (including Digital Apparatus) SAE Composite Materials Handbook, Volume 2, 201 U.S. Code of Federal Regulations, Title 47 Part 15 (CFR Part 15), Radio Frequency Devices