CSA E60730-2-14:20

1 Scope and normative references This clause of Part 1 is applicable except as follows: 1.1 Replacement: This part 2-14 applies to electric actuators for use in, on, or in association with equipment for household and similar use. The equipment may use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof. NOTE Throughout this standard the word "equipment" means "appliance and equipment." EXAMPLE 1 Electric actuators for appliances within the scope of IEC 60335. This International Standard is applicable to controls for building automation within the scope of ISO 16484. This part 2-14 also applies to automatic electrical controls for equipment that may be used by the public, such as equipment intended to be used in shops, offices, hospitals, farms and commercial and industrial applications. EXAMPLE 2 Controls for commercial catering, heating and air-conditioning equipment. This part 2-14 is also applicable to individual electric actuators utilized as part of a control system or controls, which are mechanically integral with multifunctional controls having non-electrical outputs. EXAMPLE 3 Independently mounted water valves, controls in smart grid systems and controls for building automation systems within the scope of ISO 16484-2. This part 2-14 does not apply to automatic electric actuators intended exclusively for industrial process applications unless explicitly mentioned in the relevant part 2 or the equipment standard. This part 2-14 applies to electric actuators powered by primary or secondary batteries, requirements for which are contained within the standard, including Annex V. 1.1.1 This part 2-14 applies to the inherent safety, to the operating values, operating times and operating sequences where such are associated with equipment safety and to the testing of electric actuators used in or in association with equipment. NOTE Requirements for specific operating values, operating times and operating sequences may be given in the standards for appliances and equipment. This standard is also applicable to the functional safety of low complexity safety related systems and controls. This Standard also applies to electrically powered mechanisms that are designed to provide the signals needed for monitoring electrically-powered valve actuators that are designed to be fitted to valves from a remote location. Electrically-operated damper actuators are covered under the scope of this Standard. This Standard also applies to electric actuators for use in commercial and industrial applications. This Part 2-14 does not apply to electric actuators which are mechanically integrated with valves covered by a separate Part 2, e.g., CAN/CSA-E60730-2-8 or the Standard for electrically operated valves, CSA C22.2 No. 139. This Part 2-14 does not apply to electric motors, requirements for which are contained in CSA C22.2 No. 77 and CSA C22.2 No. 100. 1.1.2 Requirements for manual switches not integral with an electric actuator are contained in CAN/CSA-C22.2 No. 61058-1 or CSA C22.2 No. 55. 1.1.3 Replacement This Part 2-14 applies to electric actuators with a rated voltage not exceeding 600 V. 1.1.4 Replacement This part 2-14 does not take into account the response value of an automatic action of an electric actuator, if such a response value is dependent upon the method of mounting the electric actuator in the equipment. Where a response value is of significant purpose for the protection of the user, or surroundings, the value defined in the appropriate household equipment or as determined by the manufacturer shall apply. 1.2 Normative references [Add the following to the Part 1] In this Standard, any reference to International Standards shall be replaced by the relevant National Standard of Canada. Where reference is made to CSA Group publications, such reference shall be considered to refer to the latest edition and all amendments published to that edition. This Standard refers to the following publications, and the years shown indicate the latest editions available at the time of printing: CSA Group C22.1-18 Canadian Electrical Code, Part I C22.2 No. 0:20 General requirements — Canadian Electrical Code, Part II C22.2 No. 0.8:19 Safety functions incorporating electronic technology CAN/CSA-C22.2 No. 0.17-00 (R2018) Evaluation of properties of polymeric materials C22.2 No. 55-15 (R2020) Special use switches C22.2 No. 77-14 (R2019) Motors with inherent overheating protection C22.2 No. 100-14 (R2019) Motors and generators C22.2 No. 139:19 Electrically operated valves CSA/ANSI Z21.21:19/CSA 6.5:19 Automatic valves for gas appliances The following National Standards of Canada, published by CSA Group, are adoptions of IEC Standards. The requirements of these CSA Group Standards shall take precedence over the International Standards on which they are based. Any reference within CSA E60730-2-14 to the International Standard shall be replaced by a reference to the equivalent Canadian Standard. CAN/CSA-C22.2 No. 61058-1:17 Switches for appliances — Part 1: General requirements CAN/CSA-E60730-1:15 Automatic electrical controls — Part 1: General requirements CAN/CSA-CISPR 22:10 (R2019) Information technology equipment — Radio disturbance characteristics — Limits and methods of measurement CAN/CSA-E60730-2-8:17 Automatic electrical controls for household and similar use — Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements IEC (International Electrotechnical Commission) CISPR 14-1:2016 Electromagnetic compatibility — Requirements for household appliances, electric tools and similar apparatus — Part 1: Emission