Road vehicles — Local Interconnect Network (LIN) — Part 3: Protocol specification
ISO 17987-3:2016 specifies the LIN protocol including the signal management, frame transfer, schedule table handling, task behaviour and status management and LIN master and slave node. It contains also OSI layer 5 properties according to ISO 14229‑7 UDSonLIN-based node configuration and identification services (SID: B016 to B816) belonging to the core protocol specification.
A node (normally a…
Road vehicles — Local Interconnect Network (LIN) — Part 4: Electrical physical layer (EPL) specifica...
ISO 17987-4:2016 specifies the 12 V and 24 V electrical physical layers (EPL) of the LIN communications system.
The electrical physical layer for LIN is designed for low-cost networks with bit rates up to 20 kbit/s to connect automotive electronic control units (ECUs). The medium that is used is a single wire for each receiver and transmitter with reference to ground.
ISO 17987-4:2016 includes…
Road vehicles — Local Interconnect Network (LIN) — Part 2: Transport protocol and network layer serv...
ISO 17987-2:2016 specifies a transport protocol and network layer services tailored to meet the requirements of LIN‑based vehicle network systems on local interconnect networks. The protocol specifies an unconfirmed communication.
The LIN protocol supports the standardized service primitive interface as specified in ISO 14229‑2.
ISO 17987-2:2016 provides the transport protocol and network layer…
Fibre-reinforced plastics — Determination of the plain-pin bearing strength
This International Standard specifies a procedure for determining the plain-pin bearing strength of
fibre-reinforced plastic composites.
The method described in this International Standard is applicable to fibre-reinforced plastic composites
with either thermoset or thermoplastic matrices.
Unplasticized polyamide (PA-U) pipes — Effect of time and temperature on the expected strength
This International Standard specifies the minimum values for expected strength as a function of time
and temperature in the form of reference lines, for use in calculations on pipes made of: - unplasticized
Polyamide (PA-U 180). Note: PA-U 180 follows ISO 16486-1 and covers both PA-U11 180 and PA-U12 180
Fibre-reinforced plastic composites — Determination of open-hole compression strength
ISO 12817:2013 specifies the test method to determine the open-hole compressive strength of laminated fibre-reinforced plastic composites. The laminate is intended to be a balanced and symmetrical lay-up or be otherwise homogeneous through the thickness. ISO 12817:2013 applies to all textile diameter fibre types (carbon, glass, aramids, etc.) and matrices (e.g. thermoset, thermoplastic) that meet…
Ships and marine technology — Performance test procedures of LNG BOG re-liquefaction system on board...
This document specifies test requirements and procedures for the performance test that shall be conducted in order to confirm the mechanical features of the LNG BOG re-liquefaction system on board a ship. This test procedure would be prepared to document the function and safety processes required by international standards and/or any administration for LNG BOG re-liquefaction system of LNG ships…
Road vehicles — Local Interconnect Network (LIN) — Part 7: Electrical Physical Layer (EPL) conforman...
ISO 17987-7:2016 specifies the conformance test for the electrical physical layer (EPL) of the LIN communications system. It is part of this document to define a test that considers ISO 9646 and ISO 17987‑4.
The purpose of ISO 17987-7:2016 is to provide a standardized way to verify whether a LIN bus driver is compliant to ISO 17987?4. The primary motivation is to ensure a level of…
This document describes a simplified routine method applicable to the dynamic or static sampling, by manual or mechanical means, of cereals, pulses and cereal products for assessment of their quality and condition. It is applicable to sampling for the determination of heterogeneously distributed contaminants, undesirable substances and parameters usually homogenously distributed, such as those…
