Crosslinked Polyethylene (PEX) Tubing Systems for Pressure Applications
1. Scope
1.1
This Standard provides requirements for crosslinked polyethylene pressure
tubing systems. Components are made in one standard dimension ratio (SDR 9)
and are intended for use in potable water distribution systems at a maximum
working temperature of 82°C and 690 kPa (100 psi).
Note: The pressure rating for water at 23°C and 93°C is given in Appendix A.
1.2
The components…
1. SCOPE
1.1 This standard applies to an anticorrosive vinyl primer for use on
pretreated metal under corrosive conditions.
1.2 The testing and evaluation of a product against this standard may
require the use of materials and/or equipment that could be hazardous. This
document does not purport to address all the safety aspects associated with its
use. Anyone using this…
Information technology — Enhanced communications transport service definition
This Recommendation | International Standard defines in an abstract way the externally visible service provided by the
Transport Layer in terms of:
a) the primitive actions and events of the service;
b) the parameter data associated with each primitive action and event;
c) the relationship between, and the valid sequences of, these actions and events.
The service defined in this Recommendation |…
Information technology - Enhanced communications transport service definition
This Recommendation | International Standard defines in an abstract way the externally visible service provided by the
Transport Layer in terms of:
a) the primitive actions and events of the service;
b) the parameter data associated with each primitive action and event;
c) the relationship between, and the valid sequences of, these actions and events.
The service defined in this Recommendation |…
1. SCOPE
1.1 This standard applies to three types of distillate fuel oils suitable for
use in liquid-fuel-burning equipment without preheating, and three types of
fuel oils which may contain residual fuel components and may require
preheating.
1.2 The fuel oils covered by this standard are intended for use in oil-burning
equipment for the generation of heat for domestic and industrial…
1. SCOPe
1.1 This standard applies to two types of light petroleum distillates.
1.2 The light petroleum distillates covered by this standard are intended
for use in critical applications as described below.
1.2.1 Type No. 1-K Kerosene is intended for use in unvented space heaters
certified to CAN/CSA-B140.9.3-M, when used with proper maintenance in
well-ventilated…
1. SCOPE
1.1 This standard applies to an enamel suitable for use as a finish coat on
the exterior and interior of ships and boats, and the exterior of deck
machinery and equipment exposed in marine atmospheres and intermittently
immersed in sea water.
1.2 The enamel may be applied over the following substrates:
a. aluminum primed with a primer conforming to CAN/CGSB-1.132…
1. SCOPE
1.1 This standard applies to a ready-mixed organic zinc-rich coating for
general use on steel surfaces.
1.2 The coating is intended for repair of damaged steel surfaces which are
coated with zinc-rich or galvanized coating.
1.3 The coating is intended for use in conditions subjected to normal and
marine atmospheric exposures up to a maximum temperature of 95°C…
Methods of Testing Petroleum and Associated Products
Standard Test Method for the Identification of...
1. SCOPE
1.1 This test method is a standard procedure for the determination of
paraffins, olefins, naphthenes, aromatics and unknowns (P.O.N.A.U.) in
automotive gasolines using gas chromatography.
1.2 The final boiling point of samples should not exceed that of nC15.
1.3 Individual hydrocarbon components or groups of coeluting components
greater than or equal to 0.01% by mass are…
1. SCOPE
1.1 This standard applies to a mixture of organic liquids for use as a
solvent or thinner for coatings formulated with vinyl resins.
1.2 The thinner is intended for use in reducing vinyl anticorrosive primers
and vinyl antifouling paint conforming to CAN/CGSB-1.122 and CAN/CGSB-1.123
respectively.
1.3 The testing and evaluation of a product against this standard may…