Thermal Efficiencies of Industrial and Commercial Gas-Fired Package Furnaces
1. SCOPE
This standard applies to package furnaces. For the purpose of this standard, a
package furnace is a gas-fired, warm-air furnace with an input rate exceeding
400,000 Btu per hour (117.2 kW) for installation in commercial or industrial
structures. It is supplied by one manufacturer as a complete self-contained
unit, including burner, controls, heat exchange section, and is usually…
Cross-Linked Polyethylene (PEX) Tubing Systems for Pressure Applications
1. Scope
1.1
This Standard covers cross-linked polyethylene pressure tubing systems.
Components are made in one standard dimension ratio (SDR 9) and are intended
for use in potable water distribution systems at a maximum working temperature
of 82°C and 690 kPa (100 psi).
Note: Pressure rating for water at 23°C and 93°C is given in Appendix A.
1.2
The components covered by this…
1. SCOPE
1.1 This standard applies to alkyd varnish for general interior use on
furniture, woodwork and wood floors.
1.2 Type 1, gloss and type 2, semigloss are intended for general use. Type
2, semigloss cannot be used on floors.
1.3 If better wear properties are desired then polyurethane coating
conforming to CAN/CGSB-1.175, CAN/CGSB-1.176 or to…
1. SCOPE
1.1 This standard applies to a gloss enamel suitable for use on primed or
previously painted interior surfaces, with the exception of floors.
1.2 The enamel is intended for interior use only, particularly for
kitchens, bathrooms, wood trim and dados.
1.3 The testing and evaluation of a product against this standard may
require the use of…
1. SCOPE
1.1 This standard applies to a clear one-package pre-reacted type
polyurethane coating for interior use only.
1.2 The coating is intended for use on wood furniture, panelling and
woodwork. Type 1 gloss coating is recommended for floors, but where a
satin finish is desired, Type 2 coating may be used as the final coat.
1.3 The testing and…
1. SCOPE
1.1 This standard applies to a durable weather-resistant exterior
water-borne enamel for use on primed or previously coated surfaces,
with the exception of floors.
1.2 The testing and evaluation of a product against this standard may
require the use of materials and/or equipment that could be hazardous.
This document does not purport to…
1. SCOPE
1.1 This standard applies to solid-hide and semi-transparent stains for
exterior (Type 1) or interior (Type 2) use on wooden surfaces as
decorative and protective finishes. Some stains may meet the
requirements for both Type 1 and Type 2 material.
1.2 The testing and evaluation of a product against this standard may
require the use of…
1. SCOPE
1.1 This standard states the minimum requirements for performance of
fireline workwear worn for protection against the adverse effects to
the firefighter's body during forest firefighting.
1.1.1 This standard establishes performance requirements and test methods for
evaluation of components used to construct workwear.
1.1.2 Workwear meeting this…
Recommended Practices for the Provision and Use of Fireline Workwear for Forest
Firefighters
1. SCOPE
1.1 These recommended practices provide guidance for the selection, use,
maintenance, retirement, and understanding of the limitations of
fireline workwear for protection against the adverse effects to the
firefighter's body during forest firefighting.
1.2 The use of workwear for protection against the adverse effects of fire
to the…
1. Scope
1.1 This standard specifies the requirements for a concentrated dishwashing
rinse additive used in the final rinse cycle of mechanical dishwashing
machines equipped with a suitable rinse injector device. The additive
aids in eliminating water spotting and filming of tableware in water of
any hardness.
1.2 The testing and evaluation of a product…