1.1
This Standard covers plastic plumbing fixtures and specifies requirements for materials, construction, performance, testing, and markings.
1.2
This Standard covers the following plumbing fixtures:
a)
bathtubs and combination tub/showers;
b)
lavatories;
c)
shower bases and shower stalls;
d)
sinks:
i)
bar sinks;
ii)
kitchen sinks;
iii)
laundry sinks; and
iv)
service sinks;
e…
1.1
This Standard establishes requirements for area measurement in health care facilities (HCFs). It is intended to provide a basic, uniform system to
a)
support HCF planning and design activities that require such measurements (e.g., functional programming, building and room design, administration, cost estimating, and funding of capital programs); and
b)
facilitate meaningful comparisons…
Non-recirculating direct gas-fired heating and forced ventilation appliances for commercial and indu...
1.1
This Standard applies to newly produced, non-recirculating direct gas-fired heating and forced ventilation appliances, hereinafter referred to as heaters, whose purpose is to address building infiltration, replace building air that is exhausted, offset building conduction heat loss and provide outside air ventilation. All air to the heater is ducted directly from outdoors and the products of…
1.1 General
This Standard contains performance requirements for the material, design, marking, and testing of serially produced, refillable containers intended only for the storage of liquefied natural gas for medium- and heavy-duty vehicle operation.
1.2 Construction or materials
All specifications as to construction or materials may be satisfied by any construction or materials that will…
Compressed natural gas vehicle (NGV) fueling connection devices
1.1
This Standard applies to newly produced compressed Natural Gas Vehicle (NGV) fueling connection devices, hereinafter referred to as “devices”, constructed entirely of new, unused parts and materials. NGV fueling connection devices consist of the following components, as applicable:
a)
receptacle and protective cap (mounted on vehicle) (see Clause 4.4);
b)
nozzle (see Clause 4.2); and
c…
1.1
This Standard applies to non-conductive optical fiber cable and conductive optical fiber cable intended to be installed indoors in non-hazardous locations in accordance with CSA C22.1, Canadian Electrical Code, Part I.
This Standard provides performance requirements for products installed in accordance with Section 56 of the Canadian Electrical Code, Part I.
1.2
This Standard does not…
1.1
This Standard applies to exterior bond, all-veneer plywood that has a minimum of three plies and whose outermost plies have parallel grain direction.
1.2
This Standard specifies requirements for
a)
a quality system;
b)
ply species;
c)
materials;
d)
panel construction;
e)
bonding;
f)
veneer and panel grades;
g)
dimensions and tolerances;
h)
marking; and
i)
testing.
1.3…
1.1
This Standard applies to exterior bond, all-veneer plywood with a minimum of three plies and parallel grain direction of the face and back plies.
1.2
This Standard specifies requirements for
a)
a quality system;
b)
ply species;
c)
materials;
d)
panel construction;
e)
bonding;
f)
veneer and panel grades;
g)
dimensions and tolerances;
h)
marking; and
i)
testing.
1.3
In…
1.1 General
This Standard establishes the principles and practices of an environmental compliance audit. It is intended to provide a consistent framework and minimum requirements for conducting ECAs to ensure that the ECAs address regulatory, as well as site-specific requirements.
1.2 Application
This Standard may be applied to any organization, its sites or operations, or processes or parts…
1.1
This Standard applies to switching and metering centres (hereafter may be referred to for convenience as metering centres or centres) rated 600 V and less, intended to be used in accordance with the Rules of the Canadian Electrical Code, Part I, in nonhazardous locations, to provide switching, overcurrent protection and metering for a number of circuits supplied from a consumer service. The…
