Electrical relays - Tests and measurements - Part 2: Mechanical tests and weighing
IEC 63522-2:2025 This part is used for testing all kinds of electrical relays and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use. This document defines a standard test method to ensure that particular mechanical properties (such as contact force, armature travel, contact gaps) and weight, are within specified limits.
Product category rules for life cycle assessment of electrical and electronic products and systems
IEC 63366:2025 defines product category rules (PCR) for electrical and electronic products and systems (EEPS) to develop Type III environmental declarations for electrical and electronic products and systems (EEPS). It specifies the process and requirements on how to conduct life cycle assessment (LCA) in the context of environmental declarations.
This document provides common rules for:
a) LCA…
Road vehicles — Local Interconnect Network (LIN) — Part 2: Transport protocol and network layer serv...
This document specifies a transport protocol and network layer services tailored to meet the requirements of LIN‑based vehicle network systems on local interconnect networks. The protocol specifies an unconfirmed communication.
The LIN protocol supports the standardized service primitive interface as specified in ISO 14229-2.
This document provides the transport protocol and network layer…
Corrosion protection of steel structures by protective paint systems — Assessment of, and acceptance...
This document specifies procedures for assessing the fracture strength of a protective paint coating of any thickness on a steel substrate of thickness not less than 3 mm. The procedures given in document are based on methods used with different types of pull-off test equipment. The results obtained using such different types of equipment are not comparable.
This document is only applicable if a…
High-voltage test techniques – Charge-based measurement of partial discharges
IEC 60270:2025 is applicable to the charge-based measurement of partial discharges which occur in electrical apparatus, components or systems when tested with alternating voltages (AC) up to 500 Hz or with direct voltage (DC).
This document:
– defines the terms used;
– defines the quantities to be measured;
– describes the measurement frequencies as well as the test and measuring circuits…
Programming languages - Prolog - Part 3: Definite clause grammar rules as an extension of ISO/IEC 13...
This document promotes the applicability and portability of Prolog grammar rules in data
processing systems that support standard Prolog as defined in ISO/IEC 13211–1:1995/Cor
1:2007/Cor 2:2012/Cor 3:2017 and ISO/IEC 13211–2:2000. This document specifies:
a) The representation, syntax, and constraints of Prolog grammar rules
b) A logical expansion of grammar rules into Prolog clauses
c) A set of…
Programming languages — Prolog — Part 3: Definite clause grammar rules as an extension of ISO/IEC 13...
This document promotes the applicability and portability of Prolog grammar rules in data
processing systems that support standard Prolog as defined in ISO/IEC 13211–1:1995/Cor
1:2007/Cor 2:2012/Cor 3:2017 and ISO/IEC 13211–2:2000. This document specifies:
a) The representation, syntax, and constraints of Prolog grammar rules
b) A logical expansion of grammar rules into Prolog clauses
c) A set of…
Road vehicles — Local Interconnect Network (LIN) — Part 4: Electrical physical layer (EPL) specifica...
This document specifies the 12 V and 24 V electrical physical layers (EPL) of the LIN communications system.
The electrical physical layer for LIN is designed for low-cost networks with bit rates up to 20 kbit/s to connect automotive electronic control units (ECUs). The medium that is used is a single wire for each receiver and transmitter with reference to ground.
Annex A provides…
Oil and gas industries including lower carbon energy — Pipeline transportation systems — Requirement...
This document presents assessment requirements and associated guidance for extending the service life of a pipeline system, as defined in ISO 13623, beyond its specified design life. It applies to both onshore and offshore rigid metallic pipelines and risers [including steel catenary risers (SCRs)].
This document is not directly applicable to the following:
— flexible pipelines;
— …
Audio, video and information technology equipment - Routine electrical safety testing in production
IEC 62911:2025 RLV contains both the official IEC International Standard and its Redline version. The Redline version is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition.
IEC 62911:2025 defines procedures for use during or after manufacturing of complete equipment, sub-assemblies or…
