Rechercher

This National Standard of Canada applies to glazing materials that have been subjected to the test methods described herein. Such test methods are intended to demonstrate minimum performance characteristics designed to reduce the likelihood of cutting and piercing injuries resulting when glazing materials used in areas of human impact (see Annex A) in building and architectural applications…

La présente Norme nationale du Canada s’applique aux produits verriers qui ont été soumis aux méthodes d’essai décrites ci-après. Ces méthodes d’essai visent à évaluer les caractéristiques de rendement minimal conçues pour réduire le risque de blessures, comme des coupures ou des perforations, résultant du bris de produits verriers utilisés dans des zones d’activité humaine (voir annexe A)…

1.1 Types This standard applies to two types of middle distillate fuel, Type 11 and Type 15, normally used in naval operations whose product parameters are influenced by international military standardization agreement NATO STANAG 1385, Guide Specification for Naval Distillate Fuels (F-75 and F-76). Type 11 and Type 15 correspond to NATO codes F-76 and F-75 respectively, and are suitable for…

1.1 Types La présente norme s’applique à deux types de combustibles de distillat moyen, les types 11 et 15, normalement utilisés dans les opérations navales, dont les critères sont régis par l’accord de normalisation militaire international de l’OTAN, STANAG 1385, Spécification de référence pour les combustibles, marine distillés (F-75 et F-76). Les combustibles de type 11 et de type 15…

1 Scope 1.1 Inclusions This Standard sets forth a set of minimum performance requirements for PFCs up to and including 32 L (8.45 US gallons) rated capacity, made from steel or plastic, and intended for re-use by consumers for the transportation and temporary outdoor storage of petroleum-based flammable and combustible liquids. It includes dual compartment PFCs for separate gas and oil storage…

1 Scope This clause of part 1 is replaced by: This standard deals with the safety of electric instantaneous water heaters for household and similar purposes and intended for heating water below boiling temperature, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. NOTE 1 - Instantaneous water heaters incorporating bare heating…

1 Domaine d’application 1.1 Inclusions Cette norme concerne les exigences d’un système de GIT pouvant être utilisées par les OSP pour répondre aux besoins de santé des travailleurs afin de prévenir et/ou de gérer l’incapacité au travail. Elle comprend des exigences et des conseils liés à la gestion des incapacités au travail découlant des blessures de stress opérationnel (BSO) et d’autres…

1 Scope 1.1 General 1.1.1 Inclusions This Standard specifies requirements for materials, design, manufacture, and testing of hoses and hose assemblies used for dispensing compressed gaseous hydrogen to vehicles. 1.1.2 Applicability of this Standard This Standard applies to hose assemblies used for connecting compressed gaseous hydrogen dispensers to fuelling nozzles and includes hose…

1 Scope 1.1 This Standard applies to metallic (copper, steel, stainless steel, and malleable iron) press-connect type fittings, and valves (hereafter referred to as fittings unless otherwise specified) for use with fuel gas systems intended for installation above ground, below ground, indoors, and outdoors. 1.2 This Standard applies to fuel gas systems rated for operating pressures not…

1 Scope 1.1 This Standard applies to newly produced gas appliance thermostats of the integral gas valve type having a maximum operating gas pressure of 1/2 psi (3.5 kPa) or electric type (see Clause 3), constructed entirely of new, unused parts and materials. This Standard does not apply to an electric type comfort heating thermostat (wallmounted) for installation remote from an appliance.…