1.1
This Standard applies to voltage and polarity testers for use in nonhazardous locations, in accordance
with the Rules of the Canadian Electrical Code, Part I, on electrical supply circuits and equipment at
points where the voltage difference does not exceed 750 V.
1.2
This Standard does not apply to devices primarily intended to measure voltage, such as those that
employ a meter…
Testing of three-phase synchronous machines during refurbishment
1.1
This Standard covers three-phase, alternating current, salient pole synchronous machines 150 kW and up, 200 through 13,800 volts, 60 and 50 Hertz and will assist in verifying the machine efficiency has been maintained.
Note: This Standard can be useful and applied with discretion to products outside the scope of this Standard.
1.2
Large 2-pole and 4-pole solid cylindrical rotor machines,…
UN pressure receptacles and multiple-element gas containers for the transport of dangerous goods
1.1
This Standard specifies requirements for the design, construction, initial inspection and testing, marking,
periodic inspection and testing, and repair of UN pressure receptacles and multiple-element gas containers
(MEGCs) for the transport of dangerous goods. Annex A specifies the regulatory requirements for the
conformity assessment system and registration requirements for manufacturers…
Polyethylene (PE) materials for piping systems — Determination of Strain Hardening Modulus in relati...
ISO 18488:2015 specifies a method for the determination of the strain hardening modulus which is used as a measure for the resistance to slow crack growth of polyethylene.
The strain hardening modulus is obtained from stress-strain curves on compression moulded samples. This International Standard describes how such measurement is performed and how the strain hardening modulus shall be determined…
Solid biofuels — Determination of moisture content — Oven dry method — Part 1: Total moisture — Refe...
ISO 18134-1:2015 describes the method of determining the total moisture content of a test sample of solid biofuels by drying in an oven and may be used when high precision of the determination of moisture content is necessary. The method described in this International Standard is applicable to all solid biofuels. The moisture content of solid biofuels (as received) is always reported based on…
Diesel engines — Fuel injection pumps and fuel injector low-pressure connections — Part 1: Threaded ...
ISO 13948-1:2015 specifies dimensions and requirements for mechanical, threaded connections used on diesel fuel injection pumps and fuel injectors for the connection of low-pressure fuel, lubrication oil or air supply.
Five types of threaded connections (types A to E) are described in this part of ISO 13948. Type A is commonly used for both pumps and injectors, while types B to E are for diesel…
Sensory analysis — Assessment (determination and verification) of the shelf life of foodstuffs
ISO 16779:2015 specifies methods for the determination and verification of the shelf life of foodstuffs by means of sensory tests. Sensory characteristics to be evaluated are changes in appearance, odour, flavour, taste, trigeminal sensation, and texture during assumed preservation periods.
It is intended to support the development of individual approaches.
ISO 16779:2015 does not purport to…
Pneumatic fluid power — Single rod cylinders, 1 000 kPa (10 bar) series, bores from 8 mm to 25 mm — ...
ISO 6432:2015 establishes a metric series of mounting dimensions required for interchangeability of commonly used pneumatic cylinders for a maximum working pressure of 1 000 kPa (10 bar).
NOTE This International Standard allows manufacturers freedom of design in metric cylinders and does not restrict technical development but provides basic guidelines.
Rubber and plastics — Analysis of multi-peak traces obtained in determinations of tear strength and ...
ISO 6133:2015 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics. The results are calculated by determining the median and range of peak values from a graphical plot of force versus time recorded during the test.
A trace for an adhesion strength test or tear strength test…
Information technology — Automatic identification and data capture techniques — Bar code verifier co...
ISO/IEC 15426-2:2015 defines test methods and minimum accuracy criteria applicable to verifiers using the methodologies of ISO/IEC 15415 for multi-row bar code symbols and two-dimensional matrix symbologies, and specifies reference calibration standards against which these should be tested. It provides for testing of representative samples of the equipment.
NOTE ISO/IEC 15426‑1 applies…