Fire detection and alarm systems — Part 13: Compatibility assessment of system components
ISO 7240-13:2005 specifies the requirements for compatibility and connectability assessment of system components that either comply with the requirements of ISO 7240 or with a manufacturer's specification where there is no ISO 7240 International Standard. ISO 7240-13:2005 includes only system requirements when these are necessary for compatibility assessment.
ISO 7240-13:2005 also specifies…
Household and similar electrical appliances - Safety - Part 2-6: Particular requirements for station...
Applicable to the safety of stationary electric cooking ranges, hobs, ovens and similar appliances, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances.
This consolidated version consists of the fifth edition (2002)
and its amendment 1 (2004). Therefore, no need to order amendment in
addition to this…
Information technology — Security techniques — IT network security — Part 4: Securing remote access
The general objectives of ISO/IEC 18028 are to extend the IT security management guidelines provided in ISO/IEC TR 13335 by detailing the specific operations and mechanisms needed to implement network security safeguards and controls in a wider range of network environments, providing a bridge between general IT security management issues and network security technical implementations.
ISO/IEC…
Information technology - Security techniques - IT network security - Part 4: Securing remote access
The general objectives of ISO/IEC 18028 are to extend the IT security management guidelines provided in ISO/IEC TR 13335 by detailing the specific operations and mechanisms needed to implement network security safeguards and controls in a wider range of network environments, providing a bridge between general IT security management issues and network security technical implementations.
ISO/IEC…
Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing (CSST)
1.1.1 This standard applies to natural and propane gas piping systems using corrugated stainless steel tubing (CSST), intended for installation in residential, commercial or industrial buildings, and including the following components as a minimum:
a. Corrugated stainless steel tubing (CSST);
b. Fittings for connection to the CSST; and
c. Striker plates (see Part IV, Definitions) to protect the…
Scope
1.1.1 This standard applies to newly produced outdoor cooking gas appliances (see Part IV, Definitions), constructed entirely of new, unused parts and materials. Outdoor cooking gas appliances submitted for examination under this standard shall be classified as either portable or stationary.
1.1.2 This standard applies to outdoor cooking gas appliances mounted to the exterior of a…
Electromagnetic Compatibility (EMC) - Part 4-11: Testing and Measurement Techniques - Voltage Dips, ...
This National Standard of Canada is equivalent to International Standard CEI/IEC 61000-4-11:2004.
1 Scope
This part of IEC 61000 defines the immunity test methods and range of preferred test levels for electrical and electronic equipment connected to low-voltage power supply networks for voltage dips, short interruptions, and voltage variations.
This standard applies to electrical and…
Compatibilité électromagnétique (CEM) - Partie 4-11: Techniques d'essai et de mesure - Essais d...
La présent norme nationale du Canada est équivalent à la norme internationale CEI/IEC 61000-4-11:2004.
1 Domaine d'application
La présente partie de la CEI 61000 définit les méthodes d'essai d'immunité ainsi que la gamme des niveaux d'essais préférés pour les matériels électriques et électroniques connectés à des réseaux d'alimentation basse tension pour les…
Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Pa...
ISO 23551-3:2005 specifies the safety, construction and performance requirements for gas/air ratio controls, pneumatic type, for inlet pressures up to and including 50 kPa, of a nominal connection size up to and including DN 250, intended for use with gas appliances using fuel gases as natural gas, manufactures gas or liquefied petroleum gas (LPG). It also describes the test procedures for…
