Electric vehicle battery swap system - Part 1: General and guidance
IEC TS 62840-1:2016(E) gives the general overview for battery swap systems, for the purposes of swapping batteries of electric road vehicles (EVs) when the vehicle powertrain is turned off and when the battery swap system is connected to the supply network at standard supply voltages according to IEC 60038 with a rated voltage up to 1 000 V AC and up to 1 500 V DC. It is applicable for battery…
Cutting tool data representation and exchange — Part 70: Graphical data layout — Layer setting for t...
ISO/TS 13399-70:2016 is intended to be used for the design of tool layouts for the simulation and the documentation of cutting tool components and cutting tool assemblies. It can be used in connection and correlation with other parts of ISO/TS 13399.
The main purpose of this layer structure is the graphical layout of cutting tool components and cutting tool assemblies to be used within tool pre-…
Flanges for waveguides - Part 2: Relevant specifications for flanges for ordinary rectangular wavegu...
IEC 60154-2:2016 specifies the dimensions of flanges for ordinary rectangular waveguide for use in electronic equipment. It covers requirements for flanges drilled before or after mounting on waveguides. It should be noted that for optimum electrical performance, post-drilling of the alignment holes after mounting is recommended. The aim of this standard is to specify for waveguide flanges the…
Small-bore connectors for liquids and gases in healthcare applications — Part 3: Connectors for ente...
ISO 80369-3:2016 specifies the dimensions and requirements for the design and functional performance of small-bore connectors intended to be used for connections on enteral medical devices and accessories.
NOTE 1 Enteral medical devices include enteral feeding sets, enteral drainage sets, enteral syringes, and patient interface devices including access ports.
It does not specify the…
1.1 The requirements of this Standard cover the design and construction of Type B (round or oval) and
Type BW Gas Vents.
1.2 Type B Gas Vents are intended for the venting of flue gases having temperatures not exceeding
245 °C, from gas fired appliances certified with draft hoods or diverters. Type B Gas Vents are also
intended for use with gas fired appliances, without draft hoods or…
Small-bore connectors for liquids and gases in healthcare applications -- Part 3: Connectors for ent...
ISO 80369-3:2016 specifies the dimensions and requirements for the design and functional performance of small-bore connectors intended to be used for connections on enteral medical devices and accessories. NOTE 1 Enteral medical devices include enteral feeding sets, enteral drainage sets, enteral syringes, and patient interface devices including access ports. It does not specify the dimensions…
Utility connections in port - Part 2: High and low voltage shore connection systems - Data communica...
IEC/IEEE 80005-2:2016 describes the data interfaces of shore and ships as well as step by step procedures for low and high voltage shore connection systems communication for non-emergency functions, where required. This standard specifies the interface descriptions, addresses and data type. This standard also specifies communication requirements on cruise ships, in annex A. Application of this…
Stationary source emissions — Determination of the mass concentration of ammonia in flue gas — Perfo...
ISO 17179:2016 specifies the fundamental structure and the most important performance characteristics of automated measuring systems for ammonia (NH3) to be used on stationary source emissions, for example, combustion plants where SNCR/SCR NOx control systems (deNOx systems) are applied. The procedures to determine the performance characteristics are also specified. Furthermore, it describes…
Thyristor valves for high voltage direct current (HVDC) power transmission - Part 2: Terminology
IEC 60700-2:2016 defines terms for thyristor valves for high-voltage direct current (HVDC) power transmission with line commutated converters most commonly based on three-phase bridge connections for the conversion from AC to DC and vice versa.
The contents of the corrigendum of June 2017 have been included in this copy.
Utility connections in port — Part 2: High and low voltage shore connection systems — Data communica...
IEC/IEEE 80005-2:2016 describes the data interfaces of shore and ships as well as step by step procedures for low and high voltage shore connection systems communication for non-emergency functions, where required. This standard specifies the interface descriptions, addresses and data type. This standard also specifies communication requirements on cruise ships, in annex A. Application of this…
