1. SCOPe
1.1 This specification applies to two types of staple removers, intended for
office use in extracting standard duty wire staples from paper and other
materials.
1.2 The testing and evaluation of a product against this specification may
require the use of materials and/or equipment that could be hazardous. This
document does not purport to address all the safety aspects…
1. Scope
1.1 This Standard applies to cord-connected, electrically heated warming pads with associated control units, for household and hospital use, to be used in nonhazardous locations, designed for nominal 120 V ac or dc circuits, in accordance with the Rules of the Canadian Electrical Code, Part I.
1.2 This Standard applies to general use electrically heated cushions incorporating one…
Performance Standard for Split-System Central Air-Conditioners and Heat
Pumps
1. Scope
1.1 This Standard applies to factory-made, air-source, air- sink, split-system, unitary air-conditioners and heat pumps, matching assemblies of the type classified in Clause 1.4, intended for air-conditioning and heating applications in buildings.
1.2 This Standard applies only to electrically driven, mechanical, vapour-compression-type systems charged with one of the…
Guide for field measurement of vibrations and pulsations in hydraulic machines (turbines, storage pu...
IEC 60994:1991 applies to any type of reaction or impulse turbine, as well as to any type of pump-turbine and storage pump, coupled to an electric generator or motor. It covers the field of vibration and pulsation tests referred to as standard tests. The contents of the corrigendum of April 1997 have been included in this copy.
Guide pour la mesure in situ des vibrations et fluctuations sur machines hydrauliques (turbines, pom...
S'applique à tout type de turbine à réaction ou à action, ainsi qu'à tout type de pompe-turbine et de pompe d'accumulation, couplée à un alternateur ou à un moteur. Couvre le domaine des essais de vibrations et de fluctuations qualifiés d'essais standards. Le contenu du corrigendum d'avril 1997 a été pris en considération dans cet exemplaire.
1. Scope
1.1 This Standard applies to special purpose enclosures for electrical equipment intended to be installed and used in non- hazardous locations in accordance with the Rules of the Canadian Electrical Code, Part I, as follows:
(a) enclosures for indoor location, Types 2, 5, 12, 12K and 13; and (b) enclosures for indoor or outdoor location, Types 3, 3R, 3S, 4, 4X, 6, and 6P.
1.2…
1.1
This Standard covers structural quality steel plates, shapes, hollow sections,
sheet piling, and bars for general construction and engineering purposes.
1.2
A number of strength levels are available under this Standard and are
designated by the minimum yield strength in ksi. The grades, types, and
strength levels normally available are shown in Table 1. Charpy V-Notch
categories…
Agricultural Tractors - Test Procedures - Part 1: Power Tests
This National Standard of Canada is equivalent to International Standard ISo
789/1-1981.
It specifies test procedures for determining the power avail[Cable at the power
take-off, drawbar and belt pulley on agricultural tractors of the wheeled,
track-laying or semi-tracklaying type.
It is permissible for the p.t.o. power test or the drawbar test to be applied
alone or in combination.…
Tractors, machinery for agriculture and forestry, powered lawn and garden
equipment - Symbols for o...
1 Scope
This part of ISO 3767 establishes the common symbols for use on operator
controls and other displays on tractors and machinery for agriculture and
forestry, and powered lawn and garden equipment as defined in ISO 3339-0 and
ISO 5395.
The symbols given apply to controls and displays common to tractors and
machinery for agriculture and forestry, and powered lawn and garden…
Terminologie française du soudage Section 3 : assemblages, préparations et soudures
Préface
Ce document est la première édition de la section 3: assemblages, préparations et soudures de la norme CSA W375-1990, Terminologie française du soudage. La section 1: discontinuités et défauts de soudage et la section 2: procédés de soudage et techniques connexes ont été publiées respectivement en 1984 et 198 6. Cette troisième section contient la grande majorité des termes et…