Electric vehicle battery swap system - Part 1: General and guidance
IEC 62840-1:2025 gives the general overview for battery swap systems, for the purposes of swapping batteries of electric road vehicles when the vehicle powertrain is turned off and when the battery swap system is connected to the supply network at standard supply voltages according to IEC 60038 with a rated voltage up to 1 000 V AC and up to 1 500 V DC.
This document is applicable for battery…
Système d’échange de batterie de véhicule électrique - Partie 1: Généralités et recommandations
IEC 62840-1:2025 donne une vue d’ensemble des systèmes d’échange de batterie qui sont destinés à échanger les batteries des véhicules routiers électriques lorsque le groupe motopropulseur du véhicule est désactivé et que le système d’échange de batterie est raccordé au réseau d’alimentation à des tensions d’alimentation normales conformes à l’IEC 60038, avec une tension assignée allant jusqu’à 1…
Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and f...
IEC 60947-3:2020+AMD1:2025 CSV applies to switches, disconnectors, switch-disconnectors and fuse-combination units and their dedicated accessories to be used in distribution circuits and motor circuits of which the rated voltage does not exceed 1 000 V AC or 1 500 V DC. This fourth edition cancels and replaces the third edition published in 2008, Amendment 1:2012 and Amendment 2:2015. This…
Scope
1.1 General
1.1.1 These requirements cover Distributed Energy Resource Systems (DER systems) that contain
multiple DER units and associated control equipment that provide electrical energy to loads within the
DER system. The DER system may utilize one or more DER units of any type. DER systems may also
provide energy to the area EPS (Electric Power System) if present. This Standard…
Domaine d’application
1.1 Généralités
1.1.1 Ces exigences s’appliquent aux systèmes de ressources énergétiques distribuées (systèmes
RED) qui contiennent plusieurs unités de RED et l’équipement de commande connexe qui fournissent de
l’énergie électrique aux charges à l’intérieur du système RED. Le système RED peut utiliser une ou
plusieurs unités RED de n’importe quel type. Les systèmes RED…
Electrical relays - Tests and measurements - Part 37: Terminal temperature rise at rated load
IEC 63522-37:2025 This part of lEC 63522 is used for testing all kinds of electrical relays and for evaluating their ability to perform under expected conditions of transportation, storage and all aspects of operational use. The object of this document is to define a standard test method to measure terminal temperature rise at rated load, included solder terminals, flat quick-connect terminations…
Standard interface for connecting charging stations to local energy management systems - Part 1: Gen...
IEC 63380-1:2025 defines the secure information exchange between local energy management systems and electric vehicle charging stations. The local energy management systems communicate to the charging station controllers via the resource manager.
This document specifies use cases, the sequences of information exchange and generic data models.
Lung ventilators and related equipment — Vocabulary and semantics — Part 2: High frequency and jet v...
This document defines terms for:
— high-frequency oscillatory ventilation (HFOV);
— percussive ventilation, including high-frequency percussive ventilation (HFPV);
— jet ventilation, including high frequency jet ventilation (HFJV);
— modes that combine high-frequency and physiological-rate ventilation.
It is applicable:
— in lung ventilator and breathing-therapy device…
Low-voltage switchgear and controlgear - Part 7-1: Ancillary equipment - Terminal blocks for copper ...
IEC 60947-7-1:2025 specifies requirements for terminal blocks and test disconnect terminal blocks according to Annex D with screw-type or screw-less-type clamping units primarily intended for industrial or similar use and to be fixed to a support to provide electrical and mechanical connection between copper conductors. It applies to terminal blocks intended to connect round copper conductors,…
Railway applications - Urban guided transport management and command/control systems - Part 2: Funct...
IEC 62290-2:2025 specifies the functional requirements of UGTMS (urban guided transport management and command/control systems) for use in urban guided passenger transport lines and networks. This document is applicable for new lines or for upgrading existing signalling and command control systems.
The IEC 62290 series specifies the functional, system and interface requirements for the command,…
