Sterilization of health care products — Radiation — Part 2:Establishing the sterilization dose
This part of ISO 11137 specifies methods for determining the minimum dose needed to achieve a specified
requirement for sterility and methods to substantiate the use of 25 kGy or 15 kGy as the sterilization
dose to achieve a sterility assurance level, SAL, of 10-6. This part of ISO 11137 also specifies methods of
sterilization dose audit used to demonstrate the continued effectiveness of the…
Road vehicles — Electrical disturbances from conduction and coupling — Part 3: Electrical transient ...
ISO 7637-3:2016 defines bench test methods to evaluate the immunity of devices under test (DUTs) to transient pulses coupled to lines other than supply lines. The test pulses simulate both fast and slow transient disturbances caused by the switching of inductive loads and relay contact bounce.
The following three test methods are described in ISO 7637-3:2016:
- capacitive coupling clamp (CCC…
Health informatics — Information security management in health using ISO/IEC 27002
ISO 27799:2016 gives guidelines for organizational information security standards and information security management practices including the selection, implementation and management of controls taking into consideration the organization's information security risk environment(s).
It defines guidelines to support the interpretation and implementation in health informatics of ISO/IEC 27002…
ISO 10254:2016 defines the terms relating to air cargo and aircraft ground equipment, as used in the other International Standards in these areas.
NOTE The term "weight" is used throughout ISO 10254:2016 instead of the correct technical term "mass", in order to conform to current commercial usage.
The terms and abridged definitions of ISO 10254:2016 are primarily…
Timber structures — Determination of characteristic values — Part 3: Glued laminated timber
ISO 12122-3:2016 gives methods for the determination of characteristic values for a defined population of glued laminated timber products, calculated from test values.
It presents methods for the determination of
a) characteristic value of mean-based properties, and
b) characteristic value of 5th percentile-based properties.
NOTE Annex B gives information on the methods that have…
Metallic materials — Tensile testing — Part 1: Method of test at room temperature
ISO 6892-1:2016 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
NOTE Annex A contains further recommendations for computer controlled testing machines.
Information technology - Reference Architecture for Service Oriented Architecture (SOA RA) - Part 3:...
ISO/IEC 18384-3:2016 defines a formal ontology for service-oriented architecture (SOA), an architectural style that supports service orientation. The terms defined in this ontology are key terms from the vocabulary in ISO/IEC 18384-1.
Information technology — Reference Architecture for Service Oriented Architecture (SOA RA) — Part 3:...
ISO/IEC 18384-3:2016 defines a formal ontology for service-oriented architecture (SOA), an architectural style that supports service orientation. The terms defined in this ontology are key terms from the vocabulary in ISO/IEC 18384-1.
High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirement...
IEC 61180:2016 is applicable to dielectric tests with direct voltage; dielectric tests with alternating voltage; dielectric tests with impulse voltage and test equipment used for dielectric tests on low-voltage equipment. This standard is applicable only to tests on equipment having a rated voltage of not more than 1 kV a.c. or 1,5 kV d.c. This standard is applicable to type and routine tests for…
Grading capacitors for high-voltage alternating current circuit-breakers - Part 1: General
IEC 62146-1:2013+A1:2016 is applicable to grading capacitors used on circuit-breakers. Their function is to control the voltage distribution across the individual interrupter units of a multi-break circuit-breaker. Grading capacitors can also be used in parallel to the interrupter unit on single break circuit-breakers to modify the Transient Recovery Voltage (TRV). The grading capacitor is a sub-…
