Plastics — Phenolic powder moulding compounds (PF-PMCs) — Part 3: Requirements for selected moulding...
This part of ISO 14526 specifies the requirements for the physical and chemical properties of phenolic powder
moulding compounds (PF-PMCs) and compression- or injection-moulded test specimens produced from them.
It is limited to those powder moulding compounds whose composition and properties are significantly different. It is
further limited to those moulding compounds which are of general…
Plastics — Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF...
This part of ISO 14527 specifies the requirements for the physical and chemical properties of urea-formaldehyde
and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) and compression- or
injection-moulded test specimens produced from them.
It is limited to those powder moulding compounds whose composition and properties are significantly different. It is
further limited to…
Plastics — Melamine-formaldehyde powder moulding compounds (MF-PMCs) — Part 3: Requirements for sele...
This part of ISO 14528 specifies the requirements for the physical and chemical properties of melamineformaldehyde
powder moulding compounds (MF-PMCs) and compression- or injection-moulded test specimens
produced from them.
It is limited to those powder moulding compounds whose composition and properties are significantly different. It is
further limited to those moulding compounds which are of…
Plastics — Melamine/phenolic powder moulding compounds (MP-PMCs) — Part 3: Requirements for selected...
This part of ISO 14529 specifies the requirements for the physical and chemical properties of phenolic powder
moulding compounds (MP-PMCs) and compression- or injection-moulded test specimens produced from them.
It is limited to those powder moulding compounds whose composition and properties are significantly different. It is
further limited to those moulding compounds which are of general…
Plastics — Unsaturated-polyester powder moulding compounds (UP-PMCs) — Part 3: Requirements for sele...
This part of ISO 14530 specifies the requirements for the physical and chemical properties of unsaturated-polyester
powder moulding compounds (UP-PMCs) and compression- or injection-moulded test specimens produced from
them.
It is limited to those powder moulding compounds whose composition and properties are significantly different. It is
further limited to those moulding compounds which are of…
Aerospace — Nuts, self-locking, with maximum operating temperature less than or equal to 425 degrees...
This International Standard specifies the required characteristics for metric self-locking nuts, with MJ threads, for
use in aerospace construction at a maximum temperature less than or equal to 425 °C.
It is applicable to nuts as defined above, provided that reference is made to this International Standard in the
relevant definition document.
Plastics — Epoxy powder moulding compounds (EP-PMCs) — Part 3: Requirements for selected moulding co...
This part of ISO 15252 specifies the requirements for the physical and chemical properties of epoxy powder
moulding compounds (EP-PMCs) and compression- or injection-moulded test specimens produced from them.
It is limited to those powder moulding compounds whose composition and properties are significantly different. It is
further limited to those moulding compounds which are of general…
Hydraulic turbines, storage pumps and pump-turbines - Model acceptance tests
IEC 60193:1999 applies to laboratory models of any type of impulse or reaction hydraulic turbine, storage pump or pump-turbine. This standard applies to models of prototype machines either with unit power greater than 5 MW or with reference diameter greater than 3 m. Full application of the procedures herein prescribed is not generally justified for machines with smaller power and size.…
Ceramic pressurized hollow insulators for high-voltage switchgear and
controlgear
This National Standard of Canada is based on International Standard CEI/IEC 1264:1994.
1 General
1.1 Scope
This standard applies to hollow insulators made of ceramic metarial, with their
fixing devices, intended for use with a permanent gas pressure greater than 0,5
bar having an internal volume equal to or greater than 1 litre (1 000 cm³).
They are intended for use in electrical…
Caplights for use in mines susceptible to firedamp - Part 1: General requirements - Construction and...
Specifies requirements for the construction and testing of caplights for use in mines susceptible to firedamp (Group I - electrical apparatus for explosive gas atmospheres as defined in IEC 60079-0). It deals only with the risk of caplight becoming a source of ignition. The requirements of IEC 60079-0 do not apply unless specified. Is also applicable to caplights intended for use in mines…