Medical electrical equipment - Part 2: Particular requirements for the safety of electrically operat...
This National Standard of Canada is equivalent to International Standard CEI/IEC 601-2-38:1996 (first edition, 1996-10).
1 Scope and object
This clause of the General Standard applies, except as follows:
1.1 Scope
Addition:
This Particular Standard specifies requirements for safety of ELECTRICALLY OPERATED HOSPITAL BEDS, hereinafter referred to as BED, as defined in 2.2.101.
1.2 Object…
Machinery for Forestry - Log Loaders - Location and Method of Operation of Two-Lever Operator Contro...
This National Standard of Canada is based on International Standard ISO 15078:1998 (first edition, 1998-07-01).
1 Scope
This International Standard specifies the operational pattern for log loader controls. Two alternative two-lever systems are specified.
This International Standard applies to two-lever control systems for grapple-type log loaders used in mobile and self-propelled…
Ophthalmic optics — Spectacle lenses — Fundamental requirements for uncut finished lenses
ISO 14889:2002 specifies fundamental requirements for uncut finished spectacle lenses. This International Standard is not applicable to protective spectacle lenses.
ISO 14889:2002 takes precedence over the corresponding requirements of other standards, if differences exist.
ISO 4527:2003 specifies the requirements and test methods for autocatalytic nickel-phosphorus alloy coatings applied from aqueous solutions on to metallic substrates.
This International Standard does not apply to autocatalytic nickel-boron alloy coatings, nickel-phosphorus composites and ternary alloys.
Road vehicles — Injury risk curves for evaluation of occupant protection in frontal impact
ISO/TR 7861:2002 presents injury risk curves that can be used for injury risk assessment in the evaluation of occupant protection in road-vehicle frontal impact. The measurements were made on frontal-impact crash test dummies which present acceptable levels of biofidelity response in accordance with ISO 12349-1 and ISO 12349-2 and which are used in the frontal-impact test procedures of existing…
Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V - Part 1: General - Per...
This National Standard of Canada is based on International Standard CEI/IEC 60871-1:1997 (second edition, 1997-10).
1 Scope and object
This part of IEC 60871 is applicable to both capacitor units and capacitor banks intended to be used, particularly, for power-factor correction of a.c. power systems having a rated voltage above 1 000 V and frequencies of 15 Hz to 60 Hz.
This part of IEC…
Medical suction equipment - Part 2: Manually powered suction equipment
This National Standard of Canada is based on International Standard ISO 10079-2:1999 (second edition, 1999-08-15).
1 Scope
This part of ISO 10079 specifies safety and performance requirements for manually powered medical suction equipment intended for oro-pharyngeal suction. It covers equipment operated by foot or by hand or both (see Figure 1). Non-electrical suction equipment which may be…
Medical suction equipment - Part 3: Suction equipment powered from a vacuum or pressure source
This National Standard of Canada is based on International Standard ISO 10079-3:1999 (second edition, 1999-08-15).
1 Scope
This part of ISO 10079 specifies safety and performance requirements for medical suction equipment powered from a vacuum or pressure source (see Figure 1).
In particular it applies to connections for pipelines and Venturi attachments. Suction equipment with components…
Anaesthetic and Respiratory Equipment - Tracheal Tubes and Connectors
This National Standard of Canada is based on International Standard ISO 5361:1999, first edition).
1 Scope
This International Standard specifies requirements for the dimensions, basic properties and method of size designation of the most commonly used types of oro-tracheal and naso-tracheal tube made of plastics materials and/or rubber (plain and cuffed), and requirements for tracheal tube…
Health and safety in welding and allied processes — Laboratory method for sampling fume and gases ge...
ISO 15011-2:2003 provides guidance on the determination of emission rates of gases generated by arc welding using a fume box technique. It describes the test principle, gives a possible fume box arrangement and considers methods for sampling and analysis.
The following gases that can be produced during arc welding are covered:
- carbon monoxide (CO);
- carbon dioxide (CO2);
- nitrogen oxide (NO…