Paper, pulp, and recycling — Decolouration test of dye coloured paper products and paper products pr...
This document defines a method for measuring the decolouration capability of commercial products, produced using paper and board dyed in mass and/or printed with dye inks.
This document does not apply to paper printed with pigment inks.
Papier, pâte et recyclage — Essai de décoloration des produits papier colorés en masse et des produi...
Le présent document définit une méthode de mesure de l'aptitude à la décoloration des produits commerciaux fabriqués à partir de papiers et de cartons teintés en masse et/ou imprimés avec des encres à colorants.
Le présent document ne s'applique pas aux papiers imprimés avec des encres pigmentaires.
Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of elastic modulus o...
This document specifies the determination of elastic modulus of ceramics at high temperatures up to 2 100 °C by using the thin wall relative C-ring method. Procedures for test piece preparation, test modes, heat rate, load rates, data collection and reporting are given.
This document applies primarily to ceramic materials including monolithic fine ceramics, refractory materials, whisker and…
General practices for the repair of water-leakage cracks in concrete structures
This document provides a guideline for the selection of a proper grout material to repair water leakage through cracks and other deformities in concrete structures. The factors relevant to the quality control of maintenance and repair of water-leakage cracks are as the following;
a) conditions of water-leakage cracks;
b) performance requirements for repair materials;
c) different types of…
Ingénierie de la sécurité incendie — Principes généraux — Partie 2: Exemple d'application à un ...
Le présent document fournit un exemple complet pour illustrer l'ISO 23932‑1.
L'exemple est celui d'un établissement de type «pressing», pour lequel l'objectif de sécurité incendie est la sécurité des personnes, tant à l'intérieur qu'à l'extérieur de l'établissement recevant du public (ERP), en cas d'incendie dans l'établissement.
NOTE Une…
Fire safety engineering — General principles — Part 2: Example of a dry-cleaning store
This document provides a complete example to illustrate ISO 23932-1.
The example is a dry-cleaning store, for which the fire safety objective is life safety, for both people located inside or outside the shop, in the event of a fire within the shop.
NOTE Generally, an FSE study is not needed for such a small shop. However, this example was chosen to demonstrate the application of ISO 23932-1 in…
Dentistry — Corrosion test methods for dental amalgam
This document gives the details of test procedures for evaluating the corrosion resistance of dental amalgam formed from products that are within the scopes of ISO 24234 and ISO 20749.
This document is not applicable to other metallic materials in which an alloy powder reacts with a liquid alloy to produce a solid metallic material intended for dental restoration.
Superconductivity - Part 7: Electronic characteristic measurements - Surface resistance of high-temp...
IEC 61788-7:2020 RLV contains both the official IEC International Standard and its Redline version. The Redline version is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition.
IEC 61788-7:2020 describes measurement of the surface resistance (Rs) of superconductors at microwave frequencies by…
Superconductivity - Part 4: Residual resistance ratio measurement - Residual resistance ratio of Nb-...
IEC 61788-4:2020 RLV contains both the official IEC International Standard and its Redline version. The Redline version is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition.
IEC 61788-4:2020 specifies a test method for the determination of the residual resistance ratio (RRR) of Nb-Ti and…
