Road vehicles — Fuse-links with axial terminals for use in 48V networks — Types SF36-70V, SF51-70V a...
This document specifies fuse-links with axial terminals (Strip fuse-links) Types SF36‑70V, SF51‑70V and SF56‑70V used in road vehicles. It establishes, for these fuse-link types, the rated current, test procedures, performance requirements, and dimensions.
This document is applicable to fuse-links with a rated voltage of 70 V DC, a rated current of 30 A to 500 A, and a breaking capacity of 2 500…
Coating powders — Part 1: Determination of particle size distribution by sieving
This document specifies a method for the determination of the particle size distribution of coating powders by sieve analysis. Particle size distributions with a maximum of less than 100 µm is determined by laser diffraction, ISO 8130‑13. This method is used especially for determining the oversize material or for the presence of contamination and can be used as a quality control procedure ("…
Coating powders — Part 7: Determination of loss of mass on stoving
This document specifies a method for the determination of loss of mass on stoving of coating powders that are to be applied by electrostatic spraying or flock spraying or fluidized bed.
The method described in this document is a simple, practical test which provides sufficiently accurate results for coating powders that lose approximately 2 % (by mass) on stoving (heating). Above 2 %, accuracy…
Coating powders — Part 11: Inclined-plane flow test
This document specifies a comparative method for determining the flow characteristic of a fused thermosetting coating powder down a plane inclined at a set angle to the horizontal.
The aim of the test method described in this document gives an indication of the degree of melt flow that can occur during the curing of the coating powder. This characteristic contributes to the surface appearance and…
Coating powders — Part 12: Determination of compatibility
This document specifies a visual method to determine the deterioration of surface quality of the final coating when mixing two different coating powders. The surface quality will depend on the following characteristics of the coating powders:
a) the chemical reactivity;
b) the chemical composition;
c) the melt properties.
The onset of the incompatibility in appearance, its nature and its…
Coating powders — Part 13: Particle size analysis by laser diffraction
This document specifies a method for the determination of the equivalent-sphere particle size distribution of coating powders by laser diffraction, for particles of the size range from 1 µm to 300 µm.
NOTE There is a possibility that particle sizes >300 µm need the use of a different optical model.
This document is specific for the measurement of coating powders and also draws attention…
This document defines special terms used in the field of coating powders.
Other terms and definitions related to paints and varnishes are given in ISO 4618.
Ships and marine technology — Major components of emergency towing arrangements
This document specifies the technical requirements, test methods, inspection rules and markings for major components of emergency towing arrangements (ETA) provided for tankers, gas carriers (LPG, LNG, etc.) and chemical vessels no less than 20 000 deadweight tonnes (DWT).
It is only applicable to emergency towing arrangements as defined in 3.1.
NOTE For any other applications, such as for…
Camera shutters — Timing — General definition and mechanical shutter measurements
This document provides a uniform basis for determining the exposure times for all types of shutters used in still cameras and contains suitable definitions of the terms used.
It specifies the exposure-time markings for all types of shutters and their tolerances.
The characteristics of all types of mechanical shutters, which are mounted in still cameras and affect the control of exposure, motion-…
Water quality — Detection and quantification of Legionella spp. and/or Legionella pneumophila by con...
This document specifies a method for the detection and quantification of Legionella spp. and L. pneumophila using a quantitative polymerase chain reaction (qPCR). It specifies general methodological requirements, performance evaluation requirements, and quality control requirements.
Technical details specified in this document are given for information only. Any other technical solutions…
