L’IEC 60086-1:2021 est destinée à normaliser les piles électriques en ce qui concerne les dimensions, la nomenclature, les configurations des bornes, les marquages, les méthodes d’essai, les caractéristiques types de fonctionnement, la sécurité et les aspects environnementaux. Le présent document spécifie d’une part les exigences pour les piles électriques. D’autre part, le présent document…
Photovoltaic modules - Extended-stress testing - Part 1: Modules
IEC TS 63209-1:2021 is intended to provide information to supplement the baseline testing defined in IEC 61215, which is a qualification test with pass-fail criteria. This document provides a standardized method for evaluating longer term reliability of photovoltaic (PV) modules and for different bills of materials (BOMs) that may be used when manufacturing those modules. The included test…
Fire hazard testing - Part 2-20: Glowing/hot-wire based test methods - Hot wire coil test method - A...
IEC TS 60695-2-20:2021 describes a test method that applies to solid electrical insulating materials of which test specimens can be provided. The test measures the time required to ignite a test specimen when it is affected by heat from an electrically heated wire wound around the test specimen. If the test specimen drips, the time at which this occurs is also recorded.
The test method can be…
Primary batteries - Part 2: Physical and electrical specifications
IEC 60086-2:2021 is applicable to primary batteries which are based on standardised electrochemical systems.
It specifies
– the physical dimensions,
– the discharge test conditions and discharge performance requirements.
The contents of the corrigendum of June 2022 have been included in this copy.
Piles électriques - Partie 2: Spécifications physiques et électriques
L'IEC 60086-2:2021 s’applique aux piles électriques qui ont recours à des systèmes électrochimiques normalisés.
Elle spécifie:
– les dimensions physiques,
– les conditions d’essai de décharge et les exigences de performance en décharge.
Le contenu du corrigendum de juin 2022 a été pris en considération dans cet exemplaire.
IEC 60086-3-5:2021 specifies dimensions, designation, methods of tests and requirements for primary batteries for watches. In several cases, a menu of test methods is given. When presenting battery electrical characteristics and/or performance data, the manufacturer specifies which test method was used.
The contents of the corrigendum of June 2023 have been included in this copy.
Integrated circuits - EMC evaluation of transceivers - Part 5: Ethernet transceivers
IEC 62228-5:2021(E) specifies test and measurement methods for EMC evaluation of Ethernet transceiver ICs under network condition. It defines test configurations, test conditions, test signals, failure criteria, test procedures, test setups and test boards. It is applicable for transceiver of the Ethernet systems
100BASE-T1 according to ISO/IEC/IEEE 8802-3/AMD1;
100BASE-TX according to ISO/IEC…
High-voltage switchgear and controlgear - Part 106: Alternating current contactors, contactor-based ...
IEC 62271-106:2021 applies to AC contactors and/or contactor-based controllers and motor-starters designed for indoor installation and operation at frequencies up to and including 60 Hz on systems having voltages above 1 kV and up to and including 24 kV. This document also includes additional requirements for outdoor installations where the equipment is housed in an additional protective…
Power line communication systems for power utility applications - Part 3: Digital Power Line Carrier...
IEC 62488-3:2021(E) applies to power line carrier terminals and networks used to transmit information over power networks including extra high, high and medium voltage (EHV/HV/MV) power lines using both digital and optionally analogue modulation systems in a frequency range between 16 kHz and 1 MHz (see also IEC 62488-1).
In many countries, power line carrier (PLC) channels represent a…
