Household and similar electrical appliances — Safety — Part 2-89: Particular requirements for commer...
1 Scope
This clause of Part 1 is replaced by the following.
This part of IEC 60335 specifies safety requirements for electrically operated commercial refrigerating
appliances and ICE-MAKERS that have an incorporated motor-compressor or that are supplied in two units
for assembly as a single appliance in accordance with the instructions (split system).
NOTE 101 Examples of appliances that are…
Appareils électrodomestiques et analogues — Sécurité — Partie 2-89 : Exigences particulières pour le...
1 Domaine d'application
L'article de la Partie 1 est remplacé par l'article ci-après.
La présente partie de l'IEC 60335 spécifie des exigences de sécurité concernant les appareils
de réfrigération électriques et les fabriques de glace à usage commercial qui ont un
motocompresseur incorporé ou qui sont fournis sous forme de deux unités en vue d'un
assemblage en un…
1 Scope
1.1 In scope
This Standard specifies performance requirements for respirators that operate in the air filtering mode for filtering particulate matter.
1.2 Out of scope
This Standard does not address the following:
a)
respirators with filters for gas/vapour removal, which will be covered in a future edition;
b)
respirators that operate in the atmosphere-supplying mode, or…
1 Scope
1.1
This Standard specifies requirements for the design and performance of complete active fall-protection systems, including travel-restraint and vertical and horizontal fall-arrest systems. This Standard is intended for engineers with expertise in designing fall-protection systems.
1.2
This Standard does not specify design or performance requirements for fall-arrest equipment or…
This National Standard of Canada applies to four grades of gasoline to which no lead or phosphorus compounds
have been added. They are intended for use in spark-ignition engines under a wide range of climatic conditions.
This standard is not intended to apply to the mixing of oxygenated gasolines and gasolines, either at the point of
retail sale or after the point of retail sale.
Gasoline…
La présente Norme nationale du Canada s’applique à quatre qualités d’essence sans plomb ni phosphore qui sont
destinées à être utilisées dans les moteurs à allumage commandé sous diverses conditions climatiques.
Cette norme ne s’applique pas au mélange d’essences et d’essences oxygénées qui s’effectue au point de vente
au détail ou après le point de vente au détail.
L’essence conforme à la…
Oxygenated automotive gasoline containing ethanol (E1-E10 and E11-E15)
This National Standard of Canada applies to two types of oxygenated gasoline, E1-E10 (“Type A”) and E11-E15
(“Type B”), to which no lead or phosphorus compounds have been added, and in which the oxygenate consists
essentially of ethanol. They are intended for use in spark-ignition engines under a wide range of climatic conditions.
Each type may be supplied in one of four grades which differ in…
Essence automobile oxygénée contenant de l’éthanol (E1-E10 et E11-E15)
La présente Norme nationale du Canada s’applique à deux types d’essence oxygénée, E1-E10 (type A) et E11-E15
(type B), sans plomb ni phosphore dont l’oxygène est apporté principalement par l’éthanol. Ces types d’essence
sont destinés à être utilisés dans les moteurs à allumage commandé sous diverses conditions climatiques. Chaque
type peut être fourni dans l’une des quatre qualités d’essence…
Special requirements for plumbing installations in health care facilities
1 Scope
1.1 General
This Standard addresses the special requirements of plumbing systems pertinent to the design, construction, operation, and maintenance of health care facilities (HCFs). This Standard specifies requirements for the following in HCFs:
a)
water supply systems, including cold water systems and hot water systems;
b)
plumbing fixtures and fittings;
c)
drainage systems;
d)…
Biotechnology — Bioprocessing — General requirements and considerations for equipment systems used i...
This document specifies minimum requirements and general considerations for equipment, consisting of hardware, software and consumables, used in the manufacturing of cells for therapeutic use. This includes equipment for processing cells for therapeutic use starting from cell isolation/selection, expansion, washing and volume reduction, from cell finish through to cryopreservation for the storage…