Needle-based injection systems for medical use — Requirements and test methods — Part 3: Containers ...
This document specifies requirements and test methods for design verification of containers and integrated fluid paths used with Needle-Based Injection Systems (NISs) according to ISO 11608-1.
It is applicable to single and multi-dose containers either filled by the manufacturer (primary container closure) or by the end-user (reservoir) (e.g. cartridges, syringes) and fluid paths that are…
Needle-based injection systems for medical use — Requirements and test methods — Part 5: Automated f...
This document specifies requirements and test methods for automated functions in needle-based injection systems with automated functions (NIS-AUTO).
General requirements are provided for all automated functions. In addition, specific requirements are provided for the following automated functions:
a) medicinal product preparation (e.g. reconstitution);
b) needle preparation;
c) needle hiding;
d)…
Needle-based injection systems for medical use — Requirements and test methods — Part 6: On-body del...
This document specifies requirements and test methods for On-Body Delivery Systems (OBDS) needle-based injection systems (NISs) for single patient use, intended for subcutaneous, intramuscular or intradermal delivery of a discrete volume (bolus) of medicinal product, through needles or soft cannulas, incorporating pre-filled or user-filled, replaceable or non-replaceable containers.
NOTE 1 …
This document specifies safety requirements and/or protective measures applicable to EDM equipment and EDM systems intended to be adopted by persons undertaking their design, construction, installation and/or supply, such as:
— manually controlled EDM die sinking or EDM drilling machines;
— numerically controlled EDM die sinking or EDM drilling machines; and
— numerically controlled EDM…
Wheelchairs — Part 19: Wheelchairs for use as seats in motor vehicles
This document specifies test methods, requirements and recommendations for wheelchairs intended for use as seats in motor vehicles related to design, performance, labelling, presale literature, user instructions and user warnings.
This document is applicable to all manual and powered wheelchairs, including scooters, which, in addition to their primary function as wheeled mobility devices, are…
Flexible water connectors with excess flow shut-off devices
1 Scope
1.1 This Standard specifies test methods and markings for flexible water connectors with excess
flow shut-off devices.
1.2 The devices covered by this Standard are intended to be used in water supply systems under
(a) continuous pressure in accessible locations; or
(b) intermittent pressure in recreational vehicles.
1.3 In this Standard, “shall” is used to express a requirement, i.e…
1 Scope
1.1
This Standard specifies performance, design, testing, marking, classification, and other requirements related to anchorage connectors in travel-restraint, fall-arrest, work-positioning, and suspended component/tie-back line systems.
1.2
The requirements of this Standard include (where applicable) anchorage connectors attached to an anchorage. Methods of verifying the actual…
Information technology — Home electronic system (HES) interfaces — Part 4-1: Common user interface a...
This document specifies an architecture for home cluster systems and for interworking among them. It specifies a cluster-to-cluster interface to enable interworking among home cluster systems and interoperability among the applications supported by these cluster systems as well as a common user interface to these cluster-system applications. This common user interface provides input and output…
Information technology - Home Electronic System (HES) interfaces - Part 4-1: Common user interface a...
ISO/IEC 10192-4-1:2022 specifies an architecture for home cluster systems and for interworking among them. It specifies a cluster-to-cluster interface to enable interworking among home cluster systems and interoperability among the applications supported by these cluster systems as well as a common user interface to these cluster-system applications. This common user interface provides input and…
Rubber hoses and hose assemblies — Wire- or textile-reinforced single-pressure types for hydraulic a...
This document specifies requirements for ten classes, four grades and seven types of wire- or textile-reinforced hydraulic hoses and hose assemblies of nominal sizes ranging from 5 to 102. Each class has a single maximum working pressure for all sizes.
They are suitable for use with:
— oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C…