Ships and marine technology — Transmitting heading devices (THDs) — Part 1: Gyro-compasses
This part of ISO 22090 specifies the construction, performance, and testing of gyro-compasses as transmitting heading device required by chapter V, SOLAS 1974 (as amended).
A Transmitting heading device (THD) is an electronic device that provides information about the ship’s true heading.
In addition to the general requirements contained in IMO Resolution A.694(17) to which IEC 60945 is…
Ships and marine technology — Transmitting heading devices (THDs) — Part 3: GNSS principles
This part of ISO 22090 specifies general requirements, construction, performance, and testing of transmitting heading device using GNSS principle as required by chapter V, SOLAS 1974 (as amended).
A transmitting heading device (THD) is an electric device that provides information about the ship's true heading.
In addition to the general requirements contained in IMO Resolution A.694(17) to…
Ships and marine technology — Transmitting heading devices (THDs) — Part 2: Geomagnetic principles
This part of ISO 22090 specifies the construction, performance, and testing of a device employing only magnetic means as transmitting heading devices required by chapter V, SOLAS 1974 (as amended).
A Transmitting Heading Device (THD) is an electronic device that provides information about the ship’s true heading.
In addition to the general requirements contained in IMO Resolution A.694(17) to…
Ships and marine technology — Gyro-compasses for high-speed craft
This International Standard specifies the construction, performance, and type testing for gyro-compass for high-speed craft required by chapter X, SOLAS 1974 (as amended).
NOTE All requirements that are extracted from the recommendations of IMO Resolutions [Resolution A.821(19) on performance standards for gyro-compasses for high-speed craft and A.694(17)] are printed in italics.
The main…
Rough-terrain trucks — Safety requirements and verification — Part 2: Slewing trucks
ISO 10896-2:2016 specifies general safety requirements for slewing rough-terrain variable-reach trucks (hereafter known as "trucks"), consisting of a lower chassis with a slewing upper structure equipped with a telescopic lifting means (pivoted boom), on which a load handling device (e.g., carriage and fork arms) is typically fitted. Fork arms and other integrated attachments are…
Oilseeds — Simultaneous determination of oil and water contents — Method using pulsed nuclear magnet...
This International Standard specifies a rapid method for the determination of the oil and water contents of commercial oilseeds using pulsed nuclear magnetic resonance (NMR). It is applicable to rapeseeds, soya beans, linseeds and sunflower seeds with a water content less than 10 %. For seeds with higher water contents, drying is necessary before the oil content can be determined by pulsed NMR.…
Medical electrical equipment — Part 2-67: Particular requirements for basic safety and essential per...
This document is applicable to the basic safety and essential performance of oxygen conserving equipment, hereafter referred to as ME equipment, in combination with its accessories intended to conserve supplemental oxygen by delivering gas intermittently and synchronized with the patient's inspiratory cycle, when used in the home healthcare environment. Oxygen conserving equipment is…
Intelligent transport systems — Definition of data elements and data frames between roadside modules...
This document specifies data elements and data frames for messages
a) exchanged between roadside modules and:
1) signal controllers,
2) traffic management centres, and/or
3) other roadside modules.
b) exchanged between traffic management centres and signal controllers.
NOTE Roadside modules can generate data based on inputs from vehicle detectors and/or probe data transmitted by…
ISO 25178-71:2017 defines Type S1 and Type S2 software measurement standards (etalons) for verifying the software of measuring instruments. It also defines the file format of Type S1 software measurement standards for the calibration of instruments for the measurement of surface texture by the areal method as defined in the areal surface texture chain of standards, chain link G.
NOTE…
Medical devices — Information to be supplied by the manufacturer
NOTE 1 There is guidance or rationale for this Clause contained in Clause A.2.
This document specifies the requirements for information supplied by the manufacturer for a medical device or by the manufacturer for an accessory, as defined in 3.1. This document includes the generally applicable requirements for identification and labels on a medical device or accessory, the packaging,…
