Rechercher

This National Standard of Canada is equivalent to International Standard ISO/IEC 7811-6:2008. Scope ISO/IEC 7811 defines the characteristics for identification cards as defined in Clause 4 of this part of ISO/IEC 7811 and the use of such cards for international interchange. This part of ISO/IEC 7811 specifies requirements for a high coercivity magnetic stripe (including any protective overlay…

IEC/TR 80002-1:2009(E) provides guidance for the application of the requirements contained in ISO 14971:2007, Medical devices - Application of risk management to medical devices to medical device software with reference to IEC 62304:2006, Medical device software - Software life cycle processes. It does not add to, or otherwise change, the requirements of ISO 14971:2007 or IEC 62304:2006. IEC/TR…

IEC 61140:2001+A1:2004 applies to the protection of persons and animals against electric shock. It is intended to give fundamental principles and requirements which are common to electrical installations, systems and equipment or necessary for their co-ordination. Prepared for installations, systems and equipment without a voltage limit. NOTE - There are some clauses in this standard which refer…

IEC/TR 80002-1:2009(E) provides guidance for the application of the requirements contained in ISO 14971:2007, Medical devices - Application of risk management to medical devices to medical device software with reference to IEC 62304:2006, Medical device software - Software life cycle processes. It does not add to, or otherwise change, the requirements of ISO 14971:2007 or IEC 62304:2006. IEC/TR…

ISO 14813-6:2009 provides an 'enabling' structure for use in the ITS sector. It provides a formal means to enact the ISO/TC 204 decision by resolution to use ASN.1 for data definitions within ITS International Standards. This provides a common message form to enable interoperability and reuse. It provides consistency of use so that where other aspects of ASN.1 (defined within ISO/IEC…

This National Standard of Canada is based on International Standard CEI/IEC 60974-5:2009. Scope This part of IEC 60974 specifies safety and performance requirements for industrial and professional equipment used in arc welding and allied processes to feed filler wire. The wire feeder may be suitable for manually or mechanically guided torches. This part of IEC 60974 is not applicable to…

Scope 1.1 This Standard provides requirements for materials, reduced temperature performance testing, and labelling for roll-over protective structures (ROPS), falling object protective structures (FOPS), operator protective structures (OPS), and tip-over protective structures (TOPS). It also stipulates requirements for seat belts to be used in conjunction with these systems. 1.2 This Standard…

Scope 1.1 This Standard applies to insulated conductors intended for internal wiring of electrical equipment, for leads of transformers, motors, etc., and for luminous-tube signs and ignition systems, to be installed in accordance with the Canadian Electrical Code, Part I. 1.2 Constructions to which this Standard applies are shown in Tables 1 and 2. The Tables are not a complete summary of the…

Scope 1.1 General This Standard covers wrought steel buttwelding fittings, including extruded headers and factory-produced bends, primarily intended for use in oil or gas pipeline systems. 1.2 Size, grade, and category 1.2.1 Size This Standard covers fittings in sizes from NPS 1/2 to NPS 60. (See Table A.1.) 1.2.2 Grade For other than sour service, this Standard covers fittings from Grade 207…

Scope 1.1 General This Standard covers wrought steel welding neck and blind flanges primarily intended for use in oil or gas pipeline systems. 1.2 Size, grade, nominal pressure class, and category 1.2.1 Size This Standard covers flanges in sizes from NPS 1/2 to NPS 60. (See Table A.1.) 1.2.2 Grade For other than sour service, this Standard covers flanges from Grade 248 to Grade 690. For sour…