Rechercher

Affiner les résultats
Code de la Classification internationale pour les normes (ICS)
Source
Code de l’organisme d’élaboration de normes (OEN)
Langue
Statut
Code de la Norme nationale du Canada (NNC)
Date de publication

De

à

Affichage 2371 - 2380 de 5618
Household and similar electrical appliances — Safety — Part 2-27: Particular requirements for applia...
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electrical appliances incorporating emitters for exposing the skin to ultraviolet or infrared radiation, for household and similar use, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Appliances not intended for normal household…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
2016-09-30
Code(s) de l'ICS :
13.120; 97.170
Special requirements for plumbing installations in health care facilities
1.1 This Standard addresses the special requirements of plumbing systems pertinent to the design, construction, operation, and maintenance of health care facilities (HCFs). This Standard specifies requirements for the following in HCFs: a) water supply systems, including domestic cold water systems and hot water systems; b) plumbing fixtures and fittings; c) drainage systems; d) monitoring…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
2016-09-30
Code(s) de l'ICS :
01
Safeguarding of machinery
1.1 General This Standard applies to the protection of workers from the hazards arising from the use of mobile or stationary machinery. It provides the criteria to be observed and the description, selection, and application of guards and protective devices. Where a current CSA Standard exists for a specific type of machinery (e.g., CSA B167, CAN/CSA-B354.2, CSA M424.1, CSA Z142, CAN/CSA-Z248,…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
2016-09-30
Code(s) de l'ICS :
13.110
Solid biofuels — Determination of bulk density
This International Standard defines a method of determining bulk density of solid biofuels by the use of a standard measuring container. This method is applicable to all pourable solid biofuels with a nominal top size of maximum 100 mm. Bulk density is not an absolute value; therefore, conditions for its determination have to be standardized in order to gain comparative measuring results. NOTE…
Éditeur :
CSA
Statut :
Norme
Date de publication :
2016-09-30
Code(s) de l'ICS :
75.160.10; 27.190
Biocombustibles solides — Détermination de la masse volumique apparente
La présente Norme internationale définit une méthode de détermination de la masse volumique apparente des biocombustibles solides à l’aide d’un récipient-mesure standard. Cette méthode s’applique à tout biocombustible solide versable d’une dimension supérieure nominale maximale de 100 mm. La masse volumique apparente n’étant pas une valeur absolue, il est indispensable de normaliser les…
Éditeur :
CSA
Statut :
Norme
Date de publication :
2016-09-30
Code(s) de l'ICS :
75.160.10; 27.190
Petroleum and natural gas industries — Site-specific assessment of mobile offshore units — Part 1: J...
This part of ISO 19905 specifies requirements and guidance for the site-specific assessment of independent leg jack-up units for use in the petroleum and natural gas industries. It addresses: a) manned non-evacuated, manned evacuated and unmanned jack-ups; b) the installed phase at a specific site. To ensure acceptable reliability, the provisions of this part of ISO 19905 form an integrated…
Éditeur :
CSA
Statut :
Norme
Date de publication :
2016-09-30
Code(s) de l'ICS :
75.180.10
Cable management systems — Cable ties for electrical installations
This International Standard specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices used for the management and support of wiring systems in electrical installations. Cable ties and associated fixing devices may also be suitable for other applications and where so used, regard should be taken of any additional requirements. This standard…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
2016-09-30
Code(s) de l'ICS :
29.120.10; 29.120.99
HDPE conduit, conductors-in-conduit, and fittings
1.1 This Standard applies to high density polyethylene (HDPE) conduit, HDPE conduit with conductors, and fittings, intended for use at a continuous operating temperature of 75 °C or 90 °C, for installation in accordance with the Rules of the Canadian Electrical Code, Part I, for direct burial or encasement in concrete or masonry in ordinary (non-hazardous) locations. 1.2 The fittings covered…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
2016-09-30
Code(s) de l'ICS :
N/A
Explosive atmospheres — Part 7: Equipment protection by increased safety “e”
This part of IEC 60079 specifies the requirements for the design, construction, testing and marking of electrical equipment and Ex Components with type of protection increased safety “e” intended for use in explosive gas atmospheres. Electrical equipment and Ex Components of type of protection increased safety “e” are either: a) Level of Protection “eb” (EPL “Mb” or “Gb”); or b) Level of…
Éditeur :
CSA
Statut :
Norme
Date de publication :
2016-09-30
Code(s) de l'ICS :
29.260.20
Electromagnetic compatibility (EMC) — Part 4-30: Testing and measurement techniques — Power quality ...
for power quality parameters in a.c. power supply systems with a declared fundamental frequency of 50 Hz or 60 Hz. Measurement methods are described for each relevant parameter in terms that give reliable and repeatable results, regardless of the method’s implementation. This standard addresses measurement methods for in-situ measurements. Measurement of parameters covered by this standard…
Éditeur :
CSA
Statut :
Norme
Date de publication :
2016-09-30
Code(s) de l'ICS :
33.100.99

Spacer