Machinery for Forestry - Log Loaders - Location and Method of Operation of Two-Lever Operator Contro...
This National Standard of Canada is based on International Standard ISO 15078:1998 (first edition, 1998-07-01).
1 Scope
This International Standard specifies the operational pattern for log loader controls. Two alternative two-lever systems are specified.
This International Standard applies to two-lever control systems for grapple-type log loaders used in mobile and self-propelled…
Ophthalmic optics — Spectacle lenses — Fundamental requirements for uncut finished lenses
ISO 14889:2002 specifies fundamental requirements for uncut finished spectacle lenses. This International Standard is not applicable to protective spectacle lenses.
ISO 14889:2002 takes precedence over the corresponding requirements of other standards, if differences exist.
ISO 4527:2003 specifies the requirements and test methods for autocatalytic nickel-phosphorus alloy coatings applied from aqueous solutions on to metallic substrates.
This International Standard does not apply to autocatalytic nickel-boron alloy coatings, nickel-phosphorus composites and ternary alloys.
Road vehicles — Injury risk curves for evaluation of occupant protection in frontal impact
ISO/TR 7861:2002 presents injury risk curves that can be used for injury risk assessment in the evaluation of occupant protection in road-vehicle frontal impact. The measurements were made on frontal-impact crash test dummies which present acceptable levels of biofidelity response in accordance with ISO 12349-1 and ISO 12349-2 and which are used in the frontal-impact test procedures of existing…
Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V - Part 1: General - Per...
This National Standard of Canada is based on International Standard CEI/IEC 60871-1:1997 (second edition, 1997-10).
1 Scope and object
This part of IEC 60871 is applicable to both capacitor units and capacitor banks intended to be used, particularly, for power-factor correction of a.c. power systems having a rated voltage above 1 000 V and frequencies of 15 Hz to 60 Hz.
This part of IEC…
Anaesthetic and Respiratory Equipment - Tracheal Tubes and Connectors
This National Standard of Canada is based on International Standard ISO 5361:1999, first edition).
1 Scope
This International Standard specifies requirements for the dimensions, basic properties and method of size designation of the most commonly used types of oro-tracheal and naso-tracheal tube made of plastics materials and/or rubber (plain and cuffed), and requirements for tracheal tube…
Medical suction equipment - Part 2: Manually powered suction equipment
This National Standard of Canada is based on International Standard ISO 10079-2:1999 (second edition, 1999-08-15).
1 Scope
This part of ISO 10079 specifies safety and performance requirements for manually powered medical suction equipment intended for oro-pharyngeal suction. It covers equipment operated by foot or by hand or both (see Figure 1). Non-electrical suction equipment which may be…
Medical suction equipment - Part 3: Suction equipment powered from a vacuum or pressure source
This National Standard of Canada is based on International Standard ISO 10079-3:1999 (second edition, 1999-08-15).
1 Scope
This part of ISO 10079 specifies safety and performance requirements for medical suction equipment powered from a vacuum or pressure source (see Figure 1).
In particular it applies to connections for pipelines and Venturi attachments. Suction equipment with…
Health and safety in welding and allied processes — Laboratory method for sampling fume and gases ge...
ISO 15011-2:2003 provides guidance on the determination of emission rates of gases generated by arc welding using a fume box technique. It describes the test principle, gives a possible fume box arrangement and considers methods for sampling and analysis.
The following gases that can be produced during arc welding are covered:
- carbon monoxide (CO);
- carbon dioxide (CO2);
- nitrogen oxide (NO…
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 340 ...
Gives the requirements for sleeving having the property of expanding its internal diameter when compressed longitudinally and thereafter returning to its initial diameter after release of the compressing force. It is constructed of polyethylene terephthalate monofilament yarns suitably processed to provide the mechanical ability to conform in the manner described above. These sleevings have been…