Telecommunications Cabling Systems in Commercial Buildings
1 INTRODUCTION
1.1 Purpose
This standard specifies a generic telecommunications cabling system for
commercial buildings that will support a multiproduct, multivendor environment.
It also provides information that may be used for the design of
telecommunications products for commercial enterprises.
The purpose of this standard is to enable the planning and installation of a…
1.1 Purpose
This Standard establishes the principles and practices that are applicable to a
Phase I ESA. The purpose of a Phase I ESA is to identify actual and potential
site contamination. This involves the evaluation and reporting of existing
information collected through Records Review, Site Visit, and Interviews.
Phase I ESAs may assist in reducing uncertainty about potential…
Site Preparation, Foundation, and Anchorage of Mobile Homes
1.1
This Standard applies to mobile homes or modular units designed to be supported
on longitudinal floor beams.
Note: For simplicity, the term mobile home is used in the text of this
Standard.
1.2
This Standard includes requirements for the following aspects of mobile home
installation:
(a) site preparation;
(b) foundations;
(c) anchorage;
(d) connection of multiple-section units;…
Design and Installation of Earth Energy Heat Pump Systems for Commercial and
Institutional Building...
1.1
This Standard applies to unitary single-package or split-system liquid-source
heat pumps for commercial, institutional and industrial buildings over 1400 m²
(15,000 ft²), using ground-water, surface water or earth as a heat source
and/or sink for heating and/or cooling with or without a supplementary heating
or cooling system.
1.2
This Standard also applies to mechanical vapour…
Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — S...
La présente partie de l'ISO 11124 prescrit des exigences pour 12 granulométries d'abrasifs en grenaille angulaire en fonte trempée, tels qu'ils sont fournis pour la préparation par projection. Elle spécifie les tailles de particules et les désignations de granulométries correspondantes. Des valeurs sont spécifiées pour la dureté, la masse volumique, les exigences relatives aux…
Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — S...
La présente partie de l'ISO 11124 prescrit des exigences pour 14 granulométries d'abrasifs en grenaille ronde en acier coulé à haut carbone et 12 granulométries d'abrasifs en grenaille angulaire en acier coulé à haut carbone, telles qu'elles sont fournies pour la préparation par projection. Des valeurs sont spécifiées pour la dureté, la masse volumique, les exigences relatives…
1.1
This Standard specifies the minimum requirements for factory-built, single or
multiple-piece roof vent flashings used to effect a permanent weather seal
between the flashing and the vent pipe without the use of additional sealing
materials around the vent pipe. Flashings fabricated on-site are not included.
1.2
The Standard includes requirements for material, quality of work, and…
This National Standard of Canada is based on International Standard ISo
8873:1987 and the ASTM standard C 1029-90.
1. SCOPe
1.1 This standard specifies the requirements and test methods for
spray-applied rigid polyurethane cellular plastics used as thermal insulation
in building construction. The insulation is intended to be sprayed only into
open cavities or onto surfaces at the…
Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe, and
Fittings
1.1
Pertains to reinforced circular concrete pipe and fittings intended to be used
for the conveyance of sewage, industrial wastes, and storm water, and for the
construction of culverts.
Note: This Standard is applicable to manufacture and purchase only.
1.2
This Standard pertains to pipe that is intended to be used for jacking
longitudinally in tunnel operations.
Note: Such pipe may…
