Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio d...
This part of CISPR 16 is designated a basic standard, which specifies the characteristics and performance of equipment for the measurement of radiated disturbances in the frequency range 9 kHz to 18 GHz.
Specifications for ancillary apparatus are included for: antennas and test sites, TEM cells, and reverberating chambers.
The requirements of this publication shall be complied with at all…
Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio d...
This part of CISPR 16 is designated a basic standard which specifies the requirements for calibration test sites, used to perform antenna calibrations, as well as the test antenna characteristics, calibration site verification procedure and site compliance criteria. Further information on calibration site requirements, test antenna considerations and the theory of antennas and site attenuation is…
Z241.0-03 Definitions and General Safety Requirements for Park Model Trailers
1. Scope This Standard provides the definition of the term "park model trailer" as used in the CSA Z241 Series. It also gives general safety requirements that apply to the other Standards in this Series.
Z241.1-03 Vehicular Requirements for Park Model Trailers
1. Scope
1.1 Requirement Specification…
Pratique recommandée pour l'installation des systèmes de conversion d'énergie éolienne
1. Domaine d'application
1.1 Cette norme énonce les méthodes recommandées pour l'installation des systèmes de conversion d'énergie éolienne (SCEE), de même que les spécifications nécessaires.
1.2 Cette norme est destinée à être utilisée conjointement aux normes CSA pertinentes et aux notices, dessins et spécifications du fabricant, dans le but d'assurer la sécurité des…
Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of d...
ISO 4628-7:2003 describes a method suitable, in particular, for rating the degree of chalking on white or coloured exterior coatings and coating systems on rough surfaces (i.e. those having a roughness greater than segment 4 of reference comparator G as described in ISO 8503-1).
The test method specified may also be used for the assessment of the degree of chalking of coatings and coating systems…
1 Scope
1.1 General
This Standard establishes the principles and practices of an environmental compliance audit. It is intended to provide a consistent framework and minimum requirements for conducting ECAs in order to ensure that the ECAs address regulatory and liability requirements, as well as site-specific requirements.
1.2 Application
This Standard can be applied to any organization, its…
Petroleum and natural gas industries — Specific requirements for offshore structures — Part 4: Geote...
ISO 19901-4:2003 contains requirements and recommendations for those aspects of geoscience and foundation engineering that are applicable to a broad range of offshore structures, rather than to a particular structure type. Such aspects are site characterization, soil and rock characterization, and design and installation of foundations supported by the seabed (shallow foundations) and the…
Industries du pétrole et du gaz naturel — Exigences spécifiques relatives aux structures en mer — Pa...
L'ISO 19901-4:2003 contient les exigences et les recommandations relatives aux aspects géotechniques et de dimensionnement des fondations qui s'appliquent à une vaste gamme de structures en mer, plutôt qu'à un type particulier de structure. Ces aspects sont la caractérisation du site, la caractérisation des sols et des roches, le dimensionnement et installation des fondations…
Preparation of steel substrates before application of paints and related products — Surface roughnes...
ISO 8503-5:2003 describes a field method for measuring the surface profile produced by any of the abrasive blast-cleaning procedures given in ISO 8504-2. The method uses replica tape and a suitable gauge for measuring, on site, the roughness of a surface before the application of paint or another protective coating.
The method is applicable within the range of profiles cited for a given grade (or…
Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — C...
L'ISO 8503-5:2003 décrit une méthode sur site pour mesurer le profil de surface produit par l'une des méthodes de décapage par projection d'abrasif indiquées dans l'ISO 8504-2. La méthode utilise un ruban adhésif à empreinte et une jauge appropriée pour mesurer sur site la rugosité d'une surface avant l'application de la peinture ou d'un autre revêtement de…
