STANDARD FOR THERMAL INSULATION – LIGHT DENSITY, OPEN CELL SPRAY APPLIED SEMI-RIGID POLYURETHANE FOA...
1.1 This Standard specifies the requirements for the on-site manufacture and installation of light density,
open cell spray applied semi-rigid polyurethane foam to produce a material that meets the physical
property requirements of CAN/ULC-S712.1, Standard for Thermal Insulation – Light Density, Open Cell
Spray Applied Semi-Rigid Polyurethane Foam – Material Specification. The material only…
Information technology — International string ordering and comparison — Method for comparing charact...
1 Scope
This document defines the following.
— A reference comparison method. This method is applicable to two character strings to determine their collating order in a sorted list. The method can be applied to strings containing characters from the full repertoire of ISO/IEC 10646. This method is also applicable to subsets of that repertoire, such as those of the different ISO/IEC 8-bit…
1 Scope
1.1
This Standard sets forth characteristics of effective and durable installation methods, in both new and existing buildings, of fenestration products within the scope of AAMA/WDMA/CSA 101/I.S.2/A440 that are intended for installation in buildings of all occupancies to which NBC Parts 3, 4, 5, and 6 of Division B apply.
1.2
In addition to fenestration products within the scope of…
Plastics — Determination of temperature of deflection under load — Part 1: General test method
1.1 This document gives a general test method for the determination of the temperature of deflection under load (flexural stress under three-point loading) of plastics. Different types of test specimen and different constant loads are defined to suit different types of material.
1.2 ISO 75-2 gives specific requirements for plastics (including filled plastics and fibre-reinforced plastics in…
Practice for use of calorimetric dosimetry systems for dose measurements and dosimetry system calibr...
This practice covers the preparation and use of semiadiabatic calorimetric dosimetry systems for measurement of
absorbed dose and for calibration of routine dosimetry systems when irradiated with electrons for radiation processing applications.
The calorimeters are either transported by a conveyor past a scanned electron beam or are stationary in a broadened
beam.
This document is one of a set of…
Solid biofuels — Simplified sampling method for small scale applications
This document describes simplified methods for taking samples of solid biofuels in small scale applications and storages including preparation of sampling plans and reports. The main focus is on storages with a size of ≤100 t. This document is applicable to the following solid biofuels:
1) fine (up to about 10 mm nominal top size) and regularly-shaped particulate materials that can be sampled…
Diesel fuel containing low levels of biodiesel (B1–B5)
This standard applies to two types of diesel fuel, Type A, Bx and Type B, Bx. Both are suitable for use in high-speed
diesel engine powered equipment for on-road and off-road applications and in select equipment powered by medium
speed diesel engines.
Bx represents biodiesel fuel containing x percent by volume of biodiesel component in the range of 1.0 to 5.
Type A, Bx is intended for use in…
This standard applies to Type B, Bxx diesel fuel containing from 6% to 20% by volume of biodiesel. Fuel meeting
this standard is intended for use in high-speed diesel powered equipment for on-road and off-road applications and
in select equipment powered by medium-speed diesel engines.
Users of fuel meeting this standard are advised to refer to the owner’s manual of their vehicle, engine or…
This standard applies to three types of middle distillate fuel oils that are suitable for use in liquid fuel burning
equipment without preheating (Types 0, 1 and 2), and three types of fuel oils that contain residual fuel components
and require preheating (Types 4, 5 and 6).
The heating fuel oils covered by this standard are intended for use in oil burning equipment to generate heat for…
This standard applies to two types of diesel fuel, Type A and Type B. Both are suitable for use in high-speed diesel
engine powered equipment for on-road and off-road applications and in select equipment powered by medium
speed diesel engines.
Type A is intended for use in selected applications such as urban buses and underground mining or when ambient
temperatures require better low-…