Requirements for Class 1C, 2C, and 3C Pressure-Retaining Components and
Supports in CANDU Nuclear Po...
1. Scope
1.1
This Standards applies to pressure-retaining components and their supports of
CANDU nuclear power plants that have a Code Classification of Class 1C, 2C, or
3C as defined by CSA Standard N285.0.
1.2
This Standard provides rules that complement those in CSA Standards N285.0 for
the design, fabrication, installation, examination, and inspection of CANDu
nuclear power plant components…
Packaging of Infectious Substances, Diagnostic Specimens, Biological Products and Biomedical Waste f...
1. SCOPE
1.1 This standard contains requirements for the design, manufacturing and
marking for three types of means of containment used for the transportation of
Class 6.2 dangerous goods (infectious substances), diagnostic specimens,
biological products and biomedical waste.
- Type 1A (high integrity)
- Type 1B (routine)
- Type 1C (waste).
1.2 This…
1. SCOPE
1.1 This standard applies to a water-borne enamel for use as an interior
finish on primed or previously coated steel, aluminum and wood surfaces in
ships and submarines.
1.2 This enamel may be used as a water-borne alternative to enamels conforming
to CAN/CGSB-1.61.
1.3 The testing and evaluation of a product against this standard may require
the use of materials and/or…
Textile Test MethodsResistance of Materials to Water Vapour Diffusion
1. PURPOSE AND SCOPE
1.1 This method is intended for use in determining the resistance of textile
materials to water vapour diffusion.
1.2 Three options¹ are available for testing, allowing for the resistance to
water vapour diffusion of a textile material to be determined at one, or more,
of three positions within the air gap of the test apparatus.
1.3 The testing and evaluation…
1. SCOPE
1.1 This standard is intended for use as a guide when preparing
specifications and contracts for the protective coating of mild and galvanized
steels, copper and aluminum exposed to atmospheric (non-immersion) service
conditions. It contains recommendations and procedures for new coating systems
which have performed satisfactorily after long-term exposures and repair of
failed…
Pulps — Preparation of laboratory sheets for the measurement of diffuse blue reflectance factor (ISO...
This International Standard specifies two procedures for the preparation of laboratory sheets prior to measuring thediffuse blue reflectance factor (ISO brightness). One is the traditional procedure based on preparation of sheets in aBüchner funnel using a filter paper or a wire screen. ln the other procedure, the sheets are prepared in a standardsheet former (conventional or Rapid Köthen).…
1. SCOPE
1.1 This standard applies to two types¹ of diesel fuel,² SPECIAL and
SPECIAL-LS (low sulphur) for use in high- and medium-speed diesel engines in
underground mines.
1.1.1 Type SPECIAL fuel is intended for use where quantities of ventilating
air are restricted and/or high operating temperatures exist.
1.1.2 Type SPECIAL-LS (a maximum sulfur of 0.05% by mass of the SPECIAL type…
1. SCOPE
1.1 This standard applies to inorganic zinc coating for use on steel
superstructures, decks and hulls of vessels, bridges, towers, offshore drilling
rigs, tank linings and reconditioned equipment that may be exposed to
aggressive environnments, marine atmospheres and to intermittent immersion¹ in
fresh or salt water.
1.2 The coating is suitable for use in areas where…
1. SCOPE
1.1 This standard provides criteria, including dimensions, material and
structural requirements for lightweight steel wall framing components designed
for use in:
a. Non-loadbearing applications, typically the framing for interior
partitions including studs with no axial load other than self weight
and the weight of attached finishes and no lateral load…
Remanufacturing and Reconditioning of Drums Used for the Transportation ofDangerous Goods
1. SCOPE
1.1 This standard contains requirements for the remanufacturing and
reconditioning of steel and plastic drums for use in the transportation of
dangerous goods. It provides non-mandatory guidelines for the sorting of used
drums prior to processing and gives specific requirements for the
remanufacturing, reconditioning, inspection, testing and marking of drums
qualifying for…