Bunk beds and high beds — Safety requirements and tests — Part 1: Safety requirements
This document specifies requirements for the safety, strength and durability of bunk beds and high beds for domestic and non-domestic use.
It applies to bunk beds and high beds with an internal length greater than 1 400 mm and a maximum bed base width of 1 200 mm, and with the upper surface of a bed base of 600 mm or more above the floor.
Requirements for other products incorporated in a bunk bed…
Ceramic tiling systems — Sustainability for ceramic tiles and installation materials — Part 2: Speci...
This document specifies sustainability requirements together with assessment methods and evaluation schemes for ceramic tiles and installation materials.
This document includes relevant criteria across product life cycle from raw material through manufacturing, use, and end-of-life management.
This document applies to ceramic tile installation materials including: ceramic tiles, adhesives, grouts…
This document defines the requirements for the external test equipment as:
— a means of establishing communications between a WWH-OBD-equipped vehicle and external test equipment;
— a set of diagnostic services, including addressing methods, to be provided by the external test equipment in order to exercise the services defined in ISO 27145‑3.
This document describes the minimum…
Space systems — Spacecraft interface requirements document for launch vehicle services
This document provides spacecraft (SC) organizations with the general format for presenting the interface requirement document (IRD) for launch vehicle services. The IRD provides a list of the major technical requirements spacecraft agencies provide to launch vehicle (LV) agencies when submitting an application for launch services.
The IRD addresses the definition of the SC mission, the…
Information technology — Data centres — Practices for resource-efficient data centres
This document describes generally applicable practices for improving the resource efficiency of data centres, independent of their application(s).
This document focuses on continuous improvement processes, designs and guidelines that prioritize resource efficiency. In general, the processes and practices are technology-neutral and are independent of location.
The practices for data centre…
Permanence and durability of commercial prints — Part 22: Backlit display in indoor or shaded outdoo...
This document describes the test methods for light stability measurements of prints on transparent or translucent foils, sheets and paper or printed on a textile, which are displayed on backlit units installed in indoor or in shaded outdoor conditions, which are protected against direct precipitation and radiative heating. Installations of backlit display units in outdoor areas without shading,…
Analysis of natural gas — Silicon content of biomethane — Part 1: Determination of total silicon by ...
This document is applicable to the measurement of the total silicon content in gaseous matrices such as biomethane and biogas. Silicon is present in a gas phase contained predominantly in siloxane compounds, trimethylsilane and trimethylsilanol. The analytical form of the silicon measured in liquid phase after conducted sampling and derivatization procedure is soluble hexafluorosilicate anion…
Textiles et produits textiles — Microplastiques d'origines textiles — Partie 3: Mesurage de la ...
Le présent document spécifie une méthode de mesurage de la masse de matériaux collectés libérés en sortie du tuyau d’évacuation d’une machine à laver normalisée conforme à l’ISO 6330 lors du processus de lavage.
NOTE Les conditions de lavage des produits finis textiles sont indiquées par l’étiquetage d’entretien conformément à l’ISO 3758.
Le présent document est applicable aux produits…
Textiles and textile products — Microplastics from textile sources — Part 3: Measurement of collecte...
This document specifies a method for measuring the collected material mass released from the outlet hose of a standard washing machine, described in ISO 6330, through the washing process.
NOTE The washing condition of textile end products is indicated by the care labelling according to ISO 3758.
This document is applicable to textile end products (including consumer textile products,…
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts ...
This document specifies the rules for geometrical dimensioning and tolerancing of final moulded parts and parts machined out of moulded parts. It also specifies rules and conventions for the indications of these requirements in technical product documentation and specifies the proportions and dimensions of the graphical symbols to be used.
This document provides symbols for identifying the…
