THE ISO 15189:2003 Essentials - A Practical Handbook for Implementing the ISO 15189:2003 Standard fo...
Preface
This is the first edition of CSA PLUS 15189, The ISO 15189:2003 essentials.
The primary objective of this handbook is to provide both novice and experienced quality management practitioners with a concise, user-friendly guide to understanding and implementing the requirements of ISO 15189:2003.
Energy Efficiency of High-intensity Discharge (HID) and Low-pressure Sodium (LPS) Lamp Ballasts
1 Scope
1.1 This Standard applies to ballasts for high-intensity discharge (HID) and low-pressure sodium (LPS) lamps. The HID category includes mercury vapour, metal halide, and high-pressure sodium lamps.
1.2 This Standard defines the measurement technique for determining the efficiency of HID and LPS lamp ballasts for use in HID and LPS luminaires that are to be installed in industrial,…
Information technology - Generic cabling for homes
This standard specifies a generic cabling for three groups of applications in homes: Information and Communications Technologies (ICT), Broadcast and Communications Technologies (BCT), and Commands, Controls and Communications in Buildings (CCCB). It is intended to guide installations in new buildings or refurbishments, and also applies where cabling is installed to support only one or two of the…
Natural gas — Correlation between water content and water dew point
ISO 18453:2004 specifies a method to provide users with a reliable mathematical relationship between water content and water dew point in natural gas when one of the two is known. The calculation method, developed by GERG; is applicable to both the calculation of the water content and the water dew point.
ISO 18453:2004 gives the uncertainty for the correlation but makes no attempt to quantify…
Rigid cellular plastics — Determination of flexural properties — Part 1: Basic bending test
ISO 1209-1:2004 specifies a simple method for assessing the behaviour of a bar of rigid cellular plastic under the action of three-point bending.
It may be used to determine either the load for a specified deformation or the load at break.
The version of the method specified uses small test specimens and does not produce pure bending. Hence it does not permit the calculation of the flexural…
Information technology — Automatic identification and data capture techniques — Bar code print quali...
ISO/IEC 15415:2004(E) specifies two methodologies for the measurement of specific attributes of two-dimensional bar code symbols, one of these being applicable to multi-row bar code symbologies and the other to two-dimensional matrix symbologies; defines methods for evaluating and grading these measurements and deriving an overall assessment of symbol quality; and gives information on possible…
Health informatics — Trusted end-to-end information flows
ISO/TR 21089:2004 offers a guide to trusted end-to-end information flow for health(care) records and to the key trace points and audit events in the electronic entity/act record lifecycle (from point of record origination to each ultimate point of record access/use). It also offers recommendations regarding the trace/audit detail relevant to each.
It offers recommendations of best practice for…
Information technology - Automatic identification and data capture techniques - Bar code print quali...
ISO/IEC 15415:2004(E) specifies two methodologies for the measurement of specific attributes of two-dimensional bar code symbols, one of these being applicable to multi-row bar code symbologies and the other to two-dimensional matrix symbologies; defines methods for evaluating and grading these measurements and deriving an overall assessment of symbol quality; and gives information on possible…
Low-voltage switchgear and controlgear assemblies - Part 4: Particular requirements for assemblies f...
Applies to type-tested ASSEMBLIES (TTA) intended for use on construction sites, i.e. temporary places of work to which the public do not generally have access and where building construction, installation, repairs, alteration or demolition of property (buildings) or civil engineering (public works) or excavation or any other similar operations are carried out. These ASSEMBLIES may be…
Welding — Recommendations for welding of metallic materials — Part 7: Electron beam welding
ISO/TR 17671-7:2004 may be used for the electron beam welding (process No. 51 in accordance with ISO 4063) of weldable metallic materials in accordance with ISO/TR 15608. It does not contain data on permissible stresses on weld seams or on the testing and evaluation of weld seams. Such data can either be seen from the relevant user standards or should be separately agreed upon between the…
