Road vehicles — Box task and detection response task to measure visual-manual and cognitive demand
This document defines key terms and parameters applied in the analysis of cognitive and visual-manual workload induced by transport information and control systems (TICS). It provides guidelines and minimum requirements on equipment and procedures for analysing cognitive and visual-manual load including assessment of TICS to:
— plan evaluation trials;
— specify (and install) data capture…
Flexible and rigid cellular polymeric materials — Accelerated ageing tests
This document specifies, for flexible and rigid cellular polymeric materials, laboratory procedures which are intended to imitate the effects of naturally occurring reactions such as oxidation or hydrolysis by humidity. The physical properties of interest are measured before and after the application of the specified treatments.
Test conditions are only given for open cellular latex, both open-…
Implants for surgery — Partial and total hip joint prostheses — Part 12: Deformation test method for...
This part of ISO 7206 specifies a test method for determining short-term deformation of a press-fit acetabular component for total hip joint replacement under specific laboratory conditions. It also defines the conditions of testing so that the important parameters that affect the components are taken into account and it describes how the specimen is set up for testing.
The described method is…
Measurement of radioactivity — Gamma emitting radionuclides — Rapid screening method using scintilla...
ISO 19581 specifies a screening test method to quantify rapidly the activity concentration of gamma-emitting radionuclides, such as 131I, 132Te, 134Cs and 137Cs, in solid or liquid test samples using gamma-ray spectrometry with lower resolution scintillation detectors as compared with the HPGe detectors (see IEC 61563).
This test method can be used for the measurement of any potentially…
Fans — Determination of fan sound power levels under standardized laboratory conditions — Part 3: En...
ISO 13347-3:2004 applies to industrial fans as defined in ISO 5801 and ISO 13349. It is limited to the determination of airborne sound emission for the specified set-ups. Vibration is not measured, nor is the sensitivity of airborne sound emission to vibration effects determined.
The sizes of fan which can be tested in accordance with ISO 13347-3:2004 are limited only by the practical aspects of…
Healthcare organization management — Guidance for healthcare organizations’ response to the surging ...
This document provides guidance and considerations for healthcare organizations to deliver diagnostic tests timely and accurately in a pandemic by leveraging innovative approaches to overcome the limitations of laboratory capacity as follows:
– mitigating threats encountered in providing diagnostic services during a pandemic;
– consideration for quality assurance of diagnostic service provision…
Fans — Determination of fan sound power levels under standardized laboratory conditions — Part 4: So...
ISO 13347-4:2004 applies to industrial fans as defined in ISO 5801 and ISO 13349. It is limited to the determination of airborne sound emission for the specified set-ups. Vibration is not measured, nor is the sensitivity of airborne sound emission to vibration effects determined.
The sizes of the fan, which can be tested in accordance with ISO 13347-4:2004, are limited only by the practical…
Accuracy (trueness and precision) of measurement methods and results — Part 6: Use in practice of ac...
The purpose is to give some indications of the way in which accuracy data can be used in various practical situations by: giving a standard method of calculating the repeatability limit, the reproducibility limit and other limits, providing a way of checking the acceptability of test results obtained under repeatability or reproducibility conditions, describing how to assess the stability of…
Reaction to fire tests for floorings — Part 1: Determination of the burning behaviour using a radian...
This part of ISO 9239 specifies a method for assessing the wind-opposed burning behaviour and spread of flame of horizontally mounted floorings exposed to a heat flux radiant gradient in a test chamber, when ignited with pilot flames. Annex A gives details of assessing the smoke development, when required.
This method is applicable to all types of flooring, e.g. textile carpet, cork, wood,…
Paints and varnishes — Determination of pH value — Part 1: pH sensors with glass membrane
ISO 19396-1:2017 specifies a method for laboratory measurement of the pH value of polymer dispersions and coating materials using pH electrodes with a glass membrane. ISO 19396‑2 specifies a method for measuring the pH value using pH electrodes with ion-sensitive field-effect transistor (ISFET) technology.
