Information technology — Security techniques — IT network security — Part 4: Securing remote access
The general objectives of ISO/IEC 18028 are to extend the IT security management guidelines provided in ISO/IEC TR 13335 by detailing the specific operations and mechanisms needed to implement network security safeguards and controls in a wider range of network environments, providing a bridge between general IT security management issues and network security technical implementations.
ISO/IEC…
Information technology - Security techniques - IT network security - Part 4: Securing remote access
The general objectives of ISO/IEC 18028 are to extend the IT security management guidelines provided in ISO/IEC TR 13335 by detailing the specific operations and mechanisms needed to implement network security safeguards and controls in a wider range of network environments, providing a bridge between general IT security management issues and network security technical implementations.
ISO/IEC…
Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing (CSST)
1.1.1 This standard applies to natural and propane gas piping systems using corrugated stainless steel tubing (CSST), intended for installation in residential, commercial or industrial buildings, and including the following components as a minimum:
a. Corrugated stainless steel tubing (CSST);
b. Fittings for connection to the CSST; and
c. Striker plates (see Part IV, Definitions) to protect the…
Scope
1.1.1 This standard applies to newly produced outdoor cooking gas appliances (see Part IV, Definitions), constructed entirely of new, unused parts and materials. Outdoor cooking gas appliances submitted for examination under this standard shall be classified as either portable or stationary.
1.1.2 This standard applies to outdoor cooking gas appliances mounted to the exterior of a…
Electromagnetic Compatibility (EMC) - Part 4-11: Testing and Measurement Techniques - Voltage Dips, ...
This National Standard of Canada is equivalent to International Standard CEI/IEC 61000-4-11:2004.
1 Scope
This part of IEC 61000 defines the immunity test methods and range of preferred test levels for electrical and electronic equipment connected to low-voltage power supply networks for voltage dips, short interruptions, and voltage variations.
This standard applies to electrical and…
Compatibilité électromagnétique (CEM) - Partie 4-11: Techniques d'essai et de mesure - Essais d...
La présent norme nationale du Canada est équivalent à la norme internationale CEI/IEC 61000-4-11:2004.
1 Domaine d'application
La présente partie de la CEI 61000 définit les méthodes d'essai d'immunité ainsi que la gamme des niveaux d'essais préférés pour les matériels électriques et électroniques connectés à des réseaux d'alimentation basse tension pour les…
Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Pa...
ISO 23551-3:2005 specifies the safety, construction and performance requirements for gas/air ratio controls, pneumatic type, for inlet pressures up to and including 50 kPa, of a nominal connection size up to and including DN 250, intended for use with gas appliances using fuel gases as natural gas, manufactures gas or liquefied petroleum gas (LPG). It also describes the test procedures for…
Low-voltage surge protective devices - Part 1: Surge protective devices connected to low-voltage pow...
This part of IEC 61643 is applicable to devices for surge protection against indirect and direct effects of lightning or other transient overvoltages. These devices are packaged to be connected to 50/60 Hz a.c. and d.c. power circuits, and equipment rated up to 1 000 V r.m.s. or 1 500 V d.c. Performance characteristics, standard methods for testing, and ratings are established for these devices…
Parafoudres basse tension - Partie 1: Parafoudres connectés aux réseaux de distribution basse tensio...
La présente partie de la CEI 61643 est applicable aux dispositifs de protection contre les effets directs et indirects de la foudre ou contre les surtensions transitoires. Ces dispositifs sont conçus pour être connectés à des circuits sous tension alternative 50/60 Hz ou sous tension continue et à des équipements de tension assignée efficace jusqu'à 1 000 V en courant alternatif ou 1 500 V…
