Rechercher

ISO 21969:2009 applies to high-pressure flexible connections intended to be connected to cylinders or cylinder bundles with nominal filling pressures up to 25 000 kPa at 15 °C for use with the following medical gases: oxygen; nitrous oxide; air for breathing; helium; carbon dioxide; xenon; mixtures of the gases listed above; air for driving surgical tools; nitrogen for driving surgical tools;…

L'ISO 21969:2009 s'applique aux raccords flexibles haute pression destinés à être connectés à des bouteilles ou à des cadres de bouteilles dont la pression nominale de remplissage est inférieure ou égale à 25 000 kPa à 15 °C, pour utilisation avec les gaz médicaux suivants: oxygène; protoxyde d'azote; air respirable; hélium; dioxyde de carbone; xénon; mélanges des gaz énumérés ci-…

La CEI/TR 60919-3:2009 contient des indications générales sur le fonctionnement dynamique des réseaux à courant continu haute tension (CCHT). On utilise le terme fonctionnement dynamique pour désigner les événements et les phénomènes dont les fréquences caractéristiques ou la plage temporelle correspondent à un état entre des conditions transitoires et celles du régime établi. Les valves à diodes…

B137.0-09 Definitions, general requirements, and methods of testing for thermoplastic pressure piping 1 Scope 1.1 This Standard specifies requirements for thermoplastic pressure piping. It includes reference publications, definitions, abbreviations, general requirements for materials and manufactured pipe and fittings, relevant test methods, and marking requirements. Note: The terms "pipe…

IEC 60947-4-1:2009 applies to the types of equipment whose main contacts are intended to be connected to circuits the rated voltage of which does not exceed 1 000 V a.c. or 1 500 V d.c. Starters and/or contactors dealt with in this standard are not normally designed to interrupt short-circuit currents. Therefore, suitable short-circuit protection forms part of the installation but not necessarily…

IEC/TS 60034-24:2009 is applicable to the on-line detection and diagnosis of failures at the active parts of multi-phase rotating electrical machines (induction and synchronous machines) and of bearing currents. The failure analysis includes - inter-turn faults; - phase-to-phase short-circuits; - double earth faults and single earth faults of motors with earth connection of the star-point; -…

ISO 6804:2009 specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar). It is applicable to the following types of hose: Type 1: rubber hoses for unheated water supply (maximum temperature 70 °C). Type 2: rubber hoses for heated water…

Scope 1.1 This Standard applies to motor-operated appliances* intended for use with nominal system voltages of 600 V and less, except that where appliances are driven by universal-type motors or electromagnetic mechanisms, the scope is limited to appliances rated for use on nominal system voltages of 240 V or less. This Standard applies to appliances designed to be used in accordance with…

IEC 60335-2-42:2002+A1:2008 deals with the safety of electrically operated commercial forced convection ovens, steam cookers, steam-convection ovens and, exclusive of any other use, steam generators, not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. Appliances within the…

IEC/TS 61000-5-8:2009(E) provides guidance on how to protect the distributed infrastructure (power, telecommunications, transportation and pipeline networks, etc.) from the threat of a high altitude electromagnetic pulse (HEMP). In order to accomplish this goal, it is necessary to describe the special aspects of the HEMP threat to electrical/electronic systems that are connected and distributed…