Electromagnetic compatibility (EMC) - Part 3-14: Assessment of emission limits for harmonics, interh...
IEC/TR 61000-3-14:2011(E) is a Technical Report which provides guidance on principles that can be used as the basis for determining the requirements for the connection of disturbing installations to low voltage (LV) public power systems. For the purposes of this part of IEC 61000, a disturbing installation means an installation (which may be a load or a generator) that produces disturbances:…
Terminal markings for valve device stacks and assemblies and for power conversion equipment
IEC 61148:2011 is applicable to the terminal markings for the main circuits of valve device stacks and assemblies, and of integrated conversion equipment. The terminal markings refer to stacks, assemblies and equipment comprising semiconductor valve devices. The object of this standard is to specify a logical alphanumeric marking system for the identification of the external main terminals of the…
Electromagnetic compatibility (EMC) - Part 3-14: Assessment of emission limits for harmonics, interh...
IEC TR 61000-3-14:2011 is a Technical Report which provides guidance on principles that can be used as the basis for determining the requirements for the connection of disturbing installations to low voltage (LV) public power systems. For the purposes of this part of IEC 61000, a disturbing installation means an installation (which may be a load or a generator) that produces disturbances:…
1 Scope
1.1 These requirements apply to the following stationary equipment for use in nonhazardous locations
rated 7200 V or less, single- or 3-phase, and remote control assemblies for such equipment:
a) Heat pumps, for heating and cooling with or without factory, or field-installed electric
resistance heaters, or hot water or steam heating coils.
b) Air conditioners for cooling with or…
1 Scope
1.1
This Standard applies to single- or multiple-conductor, round, flat, or coiled appliance wiring material
products classified as follows:
(a) Class I — internal wiring of equipment (single- or multiple-conductor constructions with or without
an insulating covering, covering or jacket):
(i) Group A — not subject to mechanical abuse; and
(ii) Group B — potentially subject to mechanical…
1.1 Scope
1.1.1
This standard applies to newly produced direct fired construction heaters, hereinafter referred to as heaters
or appliances, constructed entirely of new, unused parts and materials and primarily intended for
temporary use in heating buildings or structures under construction, alteration or repair. All the products
of combustion generated by the heater are released into the area…
Gas-Fired Room Heaters Volume II, Unvented Room Heaters
1.1 Scope
1.1.1
This standard applies to newly produced gas-fired unvented room heaters and gas-fired unvented
decorative room heaters for connection to the house fuel supply system (see Part IV, Definitions),
hereinafter referred to as room heaters or appliances, constructed entirely of new, unused parts and
materials, having input ratings up to and including 40,000 Btu/hr (11 723 W) except:
a…
Performance standards in building — Definition and calculation of area and space indicators
ISO 9836:2011 deals with the definition and calculation of surface area and volume indicators.
In defining area measurement, ISO 9836:2011 uses three measurement concepts:
the intra-muros and extra-muros concept used in many parts of the world;
the wall centre method of measurement used in many parts of the world;
variations on these methods to comply with certain…
Information technology - Telecommunications and information exchange between systems - proxZzzy for ...
ISO/IEC 16317:2011 specifies maintenance of network connectivity and presence by proxies to extend the sleep duration of hosts.
ISO/IEC 16317:2011 specifies:
capabilities that a proxy may expose to a host;
information that must be exchanged between a host and a proxy;
proxy behaviour for 802.3 (Ethernet) and 802.11 (WiFi);
required and optional behaviour of a proxy while it is operating,…
Information technology - UPnP Device Architecture - Part 4-11: Audio Video Device Control Protocol -...
ISO/IEC 29341-4-11:2011(E) describes the service-type which enables modeling of streaming capabilities of A/V devices, and binding of those capabilities between devices. Each device that is able to send or receive a stream according to the UPnP AV Architecture will have 1 instance of the ConnectionManager service. This service provides a mechanism for control points to:…