Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la CEM - Partie...
La CEI 61326-2-4:2012 spécifie en détail, les configurations d'essai, les conditions de fonctionnement et les critères de performance pour les équipements pour le contrôle de l'isolement conforme à la CEI 61557-8 et la localisation des défauts d'isolement conformes à la CEI 61557-9. Elle s'applique aux contrôleurs d'isolement et aux systèmes de localisation des défauts d…
Information technology - Home electronic system (HES) - Guidelines for product interoperability - Pa...
ISO/IEC 18012-2:2012(E) specifies a taxonomy and application interoperability model for the interoperability of products in the area of home systems. It also specifies an interoperability framework to allow products from multiple manufacturers to work together in order to provide a specific application. It describes an application process that exists above the OSI reference model (ISO/IEC 7498-1…
Utility connections in port - Part 1: High Voltage Shore Connection (HVSC) Systems - General require...
IEC/ISO/IEEE 80005-1:2012(E) describes high voltage shore connection (HVSC) systems, on board the ship and on shore, to supply the ship with electrical power from shore. This standard is applicable to the design, installation and testing of HVSC systems and addresses:
- HV shore distribution systems;
- shore-to-ship connection and interface equipment;
- transformers/reactors;
- semiconductor/…
Fuel cell technologies - Part 3-300: Stationary fuel cell power systems - Installation
IEC 62282-3-300:2012 provides minimum safety requirements for the installation of indoor and outdoor stationary fuel cell power systems in compliance with IEC 62282-3-100 and applies to the installation of the following systems:
- intended for electrical connection to mains directly or with a readily accessible, manually operable switch or circuit-breaker;
- intended for a stand-alone power…
Technologies des piles à combustible - Partie 3-300: Systèmes à piles à combustible stationnaires - ...
La CEI 62282-3-300:2012 fournit les exigences de sécurité minimales pour l'installation intérieure et extérieure des systèmes à piles à combustible stationnaires conformément à la CEI 62282-3-100 et s'applique à l'installation des systèmes mentionnés ci-après:
- destinés à être connectés au réseau électrique directement ou via un interrupteur ou disjoncteur facilement accessible,…
Coupling capacitors and capacitor dividers - Part 1: General rules
IEC 60358-1:2012 applies to capacitors, with rated voltage >1 000 V, connected line to ground with the low voltage terminal either permanently earthed or connected to devices, for applications listed hereunder and other similar uses. This standard serves as basic standard for the coupling capacitor, the different parts of this standard will present the supplementary specifications and tests,…
Condensateurs de couplage et diviseurs capacitifs - Partie 1: Règles générales
La CEI 60358-1:2012 s'applique aux condensateurs, avec une tension assignée >1 000 V, connectés entre la ligne et la terre avec la borne basse tension connectée de manière permanente à la terre ou connectée à des dispositifs, pour les applications énumérées ci-dessous et d'autres utilisations semblables. La présente norme sert de norme de base pour le condensateur de couplage, les…
Guideline for safe operation of medical equipment used for haemodialysis treatments
IEC 62653:2012(E) which is a technical report, describes the technical requirements for use of equipment in haemodialysis, haemofiltration and haemodiafiltration. These principles should be complied with to ensure safe, permissible and proper application. The physician is responsible for the haemodialysis treatment prescription. However, the organization administering the treatment is responsible…
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping syst...
ISO 16486-1:2012 specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected…
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping syst...
ISO 16486-2:2012 specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/…
