Gas welding equipment — Rubber and plastics hose and hose assemblies for use with industrial gases u...
ISO 14113:2013 specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied, and dissolved gases up to a maximum working pressure of 450 bar (45 MPa), within the ambient temperature range of −20 °C to +60 °C.
It applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. It does…
AC motor capacitors - Part 1: General - Performance, testing andrating - Safety requirements - Guida...
IEC 60252-1:2010+A1:2013 applies to motor capacitors intended for connection to windings of asynchronous motors supplied from a single-phase system having a frequency up to and including 100 Hz, and to capacitors to be connected to three-phase asynchronous motors so that these motors may be supplied from a single-phase system. This standard covers impregnated or unimpregnated capacitors having a…
AC motor capacitors - Part 2: Motor start capacitors
IEC 60252-2:2010+A1:2013 applies to motor start capacitors intended for connection to windings of asynchronous motors supplied from a single-phase system having the frequency of the mains. Covers impregnated or unimpregnated metallized motor start capacitors having a dielectric of paper or plastic film, or a combination of both and electrolytic motor start capacitors with non-solid electrolyte,…
Road vehicles — Connection interface for pyrotechnic devices, two-way and three-way connections — Pa...
ISO 19072-2:2013 defines the performance criteria and requirements of a three-way connection interface, including ground connection, linking the pyrotechnic device and harness connector built into a road vehicle.
Performance criteria and requirements are also defined for a sealed variant of the pyrotechnic device/initiator harness connector assembly.
Performance criteria and requirements are also…
Gas cylinders — Outlet connections for gas cylinder valves for compressed breathable air
ISO 12209:2013 specifies the characteristics of outlet connections for gas cylinder valves for compressed breathable air gas cylinders. It states the fundamental requirements for both; the connection and its components and includes basic dimensions. Included in ISO 12209:2013 the following connections:
a) yoke type outlet connection for SCUBA use up to a maximum cylinder working pressure of 232…
Optical backplanes - Product specification - Part 2-1: Optical backplane using optical fibre circuit...
IEC/TS 62661-2-1:2013(E) gives guidelines for an optical backplane using optical fibre boards and multi-core right angle optical connectors with low bending loss multimode fibres (hereafter called low-loss RAO) to connect daughter boards to the optical backplane. Keywords: optical backplane, optical fibre boards, multi-core right angle optical connectors
Small craft — Permanently installed fuel systems
ISO 10088:2013 specifies the requirements for the design, materials, construction, installation and testing of permanently installed fuel systems as installed for internal combustion engines.
It applies to all parts of permanently installed diesel and petrol fuel systems as installed, from the fuel fill opening to the point of connection with the propulsion or auxiliary engine(s) on inboard- and…
Coupling capacitors and capacitor dividers - Part 2: AC or DC single-phase coupling capacitor connec...
IEC 60358-2:2013 applies to AC or DC single-phase coupling capacitors, with rated voltage > 1 000 V, connected between line and ground with a low voltage terminal either permanently earthed or connected to a device for power line carrier-frequency (PLC) applications at frequencies from 30 kHz to 500 kHz or similar applications (DC or AC) at power frequencies from 15 Hz to 60 Hz. The…
Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for cop...
IEC 60947-7-4:2013 specifies requirements for PCB terminal blocks primarily intended for industrial or similar use. Mounting and fixing on the printed circuit board is made by soldering, press-in or equivalent methods to provide electrical and mechanical connection between copper conductors and the printed circuit board.
This standard applies to PCB terminal blocks intended to connect copper…