IEC/TS 62693:2013(E) is applicable to industrial electroheating installations using electric energy as input, alone or in combination with other kinds of energy. However, external combustible fuel energy input is not dealt with, and all considerations begin at the electric only mains frequency source to which the installation is connected. Any external voltage transformation from the supply…
Space data and information transfer systems — Space Link Extension — Internet Protocol for Transfer ...
The Space Link Extension (SLE) Reference Model identifies a set of SLE Transfer Services that enable missions to send forward space link data units to a spacecraft and to receive return space link data units from a spacecraft. A subset of these services is specified by the SLE Transfer Service Recommended Standards. The SLE Transfer Service Recommended Standards specify:
the operations necessary…
Crop protection equipment — Test method for the determination of drainable volume and its concentrat...
ISO 16236:2013 specifies the test method for the determination of the volume and the concentration of the drainable volume of sprayers, in connection to the emptying of the diluted residue of the spray tank by using its outlet and other outlets allowing draining (e.g. suction filter, filling connection) at the end of the cleaning procedure.
ISO 16236:2013 applies to agricultural sprayers used for…
Surge arresters - Part 5: Selection and application recommendations
IEC 60099-5:2013 is not a mandatory standard but provides information, guidance, and recommendations for the selection and application of surge arresters to be used in three-phase systems with nominal voltages above 1 kV. It applies to gapless metal-oxide surge arresters as defined in IEC 60099-4, to surge arresters containing both series and parallel gapped structure - rated 52 kV and less as…
Surge arresters - Part 5: Selection and application recommendations
IEC 60099-5:2013 is not a mandatory standard but provides information, guidance, and recommendations for the selection and application of surge arresters to be used in three-phase systems with nominal voltages above 1 kV. It applies to gapless metal-oxide surge arresters as defined in IEC 60099-4, to surge arresters containing both series and parallel gapped structure - rated 52 kV and less as…
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -...
IEC 61300-3-50:2013 describes the procedure to measure the crosstalk of optical signals between the ports of a multiport M x N (M input ports and N output ports) fibre optic spatial switch. The crosstalk is defined as the ratio of the optical power at an output port which comes from the unconnected input port, to the optical power at the output port which comes from the connected input port.…
Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures fondamentales...
La CEI 61300-3-50:2013 décrit la procédure en vue de mesurer la diaphonie (optique) des signaux optiques entre les ports d'un commutateur spatial multiports à fibres optiques M x N (M ports d'entrée et N ports de sortie). La diaphonie est définie comme le rapport entre la puissance optique à un port de sortie qui provient du port d'entrée non connecté et la puissance optique au…
Packaging of components for automatic handling - Part 3: Packaging of surface mount components on co...
IEC 60286-3:2013 is applicable to the tape packaging of electronic components without leads or with lead stumps, intended to be connected to electronic circuits. It includes only those dimensions that are essential for the taping of components intended for the above-mentioned purposes. This standard also includes requirements related to the packaging of singulated die products including bare die…
Emballage de composants pour opérations automatisées - Partie 3: Emballage des composants pour monta...
La CEI 60286-3:2013 est applicable à la mise en bande des composants électroniques sans fils de sortie ou avec tronçons de sortie destinés à être connectés à des circuits électroniques. Elle fournit uniquement les dimensions essentielles pour la mise sur bande de composants destinés aux opérations mentionnées ci-dessus. La présente norme inclut également des exigences relatives à l'emballage…
