Dispositifs médicaux — Informations à fournir par le fabricant
NOTE 1 Il y a des indications ou une justification pour cet Article figurant dans l'Article A.2.
Le présent document spécifie les exigences relatives aux informations fournies par le fabricant pour un dispositif médical ou un accessoire, tel que défini en 3.1. Le présent document contient les exigences génériques communes concernant l’identification et l’étiquetage d’un dispositif…
Plastics — Thermomechanical analysis (TMA) — Part 3: Determination of penetration temperature
This document specifies a method for the determination of the penetration temperature of thermoplastics using thermomechanical analysis (TMA).
NOTE This method can also be used to measure the softening point.
This document establishes a model-free approach for the isoconversional kinetic analysis of chemical reactions and phase transitions. The isoconversional principle is based on the assumption that the reaction rate at a given conversion depends solely on the temperature, i.e., is independent on the heating rate.
The method is applicable to dynamic and isothermal temperature program measurements…
Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient c...
This document specifies a gradient column method for the determination of the density of non-cellular moulded or extruded plastics or pellets in void-free form. Density gradient columns are columns containing a mixture of two liquids, the density in the column increasing uniformly from top to bottom.
NOTE Density is frequently used to follow variations in physical structure or composition of…
Biotechnology — Biobanking — Requirements for human natural killer cells derived from pluripotent st...
This document specifies requirements for the biobanking of human natural killer (NK) cells derived from human pluripotent stem cells (hPSCs), including the requirements for the differentiaton, culture, characterization, quality control, storage, thawing and transport of NK cells.
Requirements for the collection of biological source material, the transport to and reception of biological source…
Pressure regulators for use with medical gases — Part 3: Pressure regulators integrated with cylinde...
This document specifies design, type testing, and marking requirements for cylinder valves with integrated pressure regulators [as defined in 3.26 and referred to hereafter as valves with integrated pressure regulators (VIPRs)] intended for the administration of medical gases in the treatment, management, diagnostic evaluation and care of patients or for gases used for driving surgical tools.…
Information technology — Information modelling for VR/AR/MR based education and training systems
This document describes guidelines for developing education and training systems using VR/AR/MR technology. It defines VR/AR/MR based information modelling that can be used for education and training systems. It provides procedures and methods to be used when developing 3D VR/AR/MR based education and training systems using ISO/IEC JTC 1 standards. It also provides a systematic approach to…
Safe design aspects for machinery in feed processing mills
This document specifies safety aspects for the design of machinery used for production of formulated feed in feed processing mills. Relevant hazards are identified with recommended solutions so as to provide the best options for the safe design during the life cycle of the machine types identified. Existing standards for safe machine design are not duplicated as machinery use for the production…
Inlet air cleaning equipment for internal combustion engines and compressors — Performance testing
This document establishes and specifies uniform test procedures, conditions, equipment and a performance report to permit the direct laboratory performance comparison of air cleaners.
The basic performance characteristics of greatest interest are air flow restriction or differential pressure, dust collection efficiency, dust capacity and oil carry-over on oil bath air cleaners. This test code…
Outils de manoeuvre pour vis et écrous — Outils dynamométriques à commande manuelle — Partie 1: Exig...
ISO 6789-1:2017 spécifie les exigences d'essai de conformité et de marquage relatives aux outils dynamométriques à commande manuelle utilisés pour le serrage contrôlé de vis et écrous. Elle spécifie également les exigences minimales relatives à la déclaration de conformité des outils dynamométriques à commande manuelle.
ISO 6789-1:2017 s'applique aux outils dynamométriques à commande…
