1.1 Connectors Included
This Standard applies to the following types of masonry connectors:
(a) ties used to interconnect the wythes of a wall;
(b) ties used to attach masonry veneer to its structural backing;
(c) anchors used to connect masonry walls to intersecting walls or to other
structural members;
(d) anchors used to attach stone to its structural backing or to interconnect
stone…
Scope
1.1 General
This Guideline provides a method for conducting environmental life cycle
analysis and assessment. It guides industry formulation of product life cycle
process stages, stage screening and problem definition, inventory analysis, and
evaluation of environmental burdens for possible improvements.
This Guideline addresses the life cycle assessment (LCA) components…
1. Scope
1.1 General
This Standard specifies requirements for mortar for use in bedding, jointing
and bonding of masonry units, or other structural units, and for grout for use
in filling core or cavity space, or both, in unit masonry construction.
Note: The term "unit masonry" refers to masonry construction using clay or
shale masonry units, sand-lime masonry units, or…
Performance of Direct-Expansion (DX) Ground-Source Heat Pumps
1.1
This Standard is intended for the performance rating of factory-assembled
unitary heat pumps, that are intended for use in direct-expansion (DX)
ground-source heat pump systems.
1.2
Within the scope of the Standard, DX heat pumps are classified as
single-package or matching assemblies that utilize indoor air as the energy
sink on heating and the energy source on cooling, and a refrigerant as…
1.1
This Standard applies to all types of fume hoods.
1.2
This Standard specifies safety requirements for fume hoods and test methods to be used to determine performance.
1.3
This Standard provides recommendations for selection, use, user education and maintenance of fume hoods.
1.4
This Standard provides recommendations for necessary information to be exchanged between the supplier…
1.1
This Standard applies to the following plumbing fixtures:
(a) bathtubs;
(b) kitchen and bar sinks;
(c) lavatories;
(d) laundry tubs;
(e) shower enclosures and receptors;
(f) drinking fountains and water coolers;
(g) water closets;
(h) bidets;
(i) urinals;
(j) non-recirculating toilets and waste-holding tanks for use in recreational
vehicles; and
(k) self-contained, recirculating…
Electric clothes washing machines for household use - Methods for measuring the performance
States and defines test methods of interest to the users for measuring the principal performance characteristics of household electric washing machines. This standard is concerned neither with safety nor with performance requirements. This standard is applicable to horizontal drum type electric clothes washing machines, to spin extractors and to washing and spinning machines for household use. It…
Test Methods for In-Line and Firebox Flame Arresters
1.1
This Standard describes test methods for use in assessing the performance of
flame arresters intended for use with Group C and D flammable gases and vapours
as defined in CSA Standard C22.1 in applications such as flare stacks, firebox
air intakes, and vent lines. This Standard does not apply to details of
construction, specification, selection, application, maintenance, or any of the…
Performance of Automatic Ice-Makers and Ice Storage Bins
1.1
This Standard applies to factory-made automatic ice-makers with a capacity
between 23 and 1000 kg (measured at standard rating conditions). These
machines produce cube, flake, crushed or fragmented ice in either a batch or
continuous process, as defined in Clause 2. They are electrically operated and
designed for a 60 Hz operating current with nominal nameplate voltage. This
standard…
1.1
This Standard provides minimum performance criteria for factory-assembled
unitary heat pumps, single-package or matching assemblies, that are
intended for application in open system and closed-loop ground-source
heat pump systems. This Standard covers equipment that has a cooling capacity
of up to 40 kW (135 000 Btu/h) at standard rating conditions, or in the case of
heating-only pumps…
