Rechercher

Affiner les résultats
Code de la Classification internationale pour les normes (ICS)
Source
Code de l’organisme d’élaboration de normes (OEN)
Langue
Statut
Code de la Norme nationale du Canada (NNC)
Date de publication

De

à

Affichage 5491 - 5500 de 6754
Energy Performance Standard for Food Service Refrigerators and Freezers
1. Scope 1.1 This Standard applies to commercial refrigerator, refrigerator-freezer, and freezer cabinets that are intended for storing or holding food products and other perishable merchandise. 1.2 This Standard applies to (a) manufacturers' standard catalogue-type equipment; (b) closed cabinets of the unitary, self-contained type; (c) commercial refrigerated storage cabinets,…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1998-09-29
Code(s) de l'ICS :
97.130.20
Capacitors for use in tubular fluorescent and other discharge lamp circuits - General and safety req...
This National Standard of Canada is based on International Standard IEC 1048:1991, including Technical Corrigendum 1:1992 and Amendment 1:1995. 1.1 Scope This International Standard states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kvar, and not less that 0,1 µF, having a rated voltage not exceeding 1 000 V,…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1998-08-31
Code(s) de l'ICS :
29.140.30; 31.060
Coal Tar-Epoxy Coating
1. SCOPE 1.1 This standard applies to cold-curing, two-component, coal tar-epoxy coatings intended for the protection of clean concrete, metal and wood surfaces that are exposed to extremely corrosive conditions. 1.2 The coal tar-epoxy coatings are suitable for application in thick coats by spray (airless and conventional) and roller, and for touch up by brush. They are intended for…
Éditeur :
ONGC
Statut :
Annulée
Date de publication :
1998-08-30
Code(s) de l'ICS :
25.220.20
Glow-starters for fluorescent lamps
This National Standard of Canada is equivalent to International Standard CEI/IEC 155: 1993. 1 Scope This standard specifies interchangeable glow-starters used with pre-heat type fluorescent lamps, hereafter called "starters". Section 1 specifies the general and safety requirements with which starters shall comply. Section 2 specifies the performance. NOTE - Starters…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1998-08-30
Code(s) de l'ICS :
29.140.30; 29.140.99
Portable Power Cables
1. Scope 1.1 This Standard specifies the construction and testing of portable power cables normally used in applications where the cables are subject to frequent flexing, and installation is in accordance with CSA Standard CAN/CSA-M421 and/or the Canadian Electrical Code, Part I. 1.2 The cable constructions specified in Clauses 4 through 8 of this Standard are suitable for use at a maximum…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1998-08-30
Code(s) de l'ICS :
29.060.20
General Requirements for Rolled or Welded Structural Quality Steel/Structural Quality Steel
1 Scope G40.20-1.1 This Standard gives a group of common requirements that apply, unless otherwise specified in a purchase order or in an individual standard, to structural quality steel plates, shapes, hollow sections, sheet, sheet piling, cold-formed channels, and bars conforming to the requirements of CSA Standard G40.21. 1.2 The values stated in either SI (metric) or yard/pound…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1998-08-30
Code(s) de l'ICS :
77.140.60; 77.140.50
Structural Quality Steel
1. Scope 1.1 This Standard covers structural quality steel plates, shapes, hollow sections, sheet piling, and bars for general construction and engineering purposes. 1.2 A number of strength levels are available under this Standard and are designated by the minimum yield strength in megapascals (ksi). The common grades, types, and strength levels are shown in Table 1. Charpy V-Notch…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1998-08-30
Code(s) de l'ICS :
77.140.60; 77.140.50
End-face image analysis procedure for the calibration of optical fibre geometry test sets
Describes the calibration of test sets which perform end-face image analysis. This is also known as near-field or grey-scale analysis. The principles may also be applied to test sets of a different type. This standard addresses the calibration of measurements made on single-mode fibres only. This type of test set may also be used to measure multimode fibres, but the evaluation of uncertainties…
Éditeur :
IEC
Statut :
Révisé
Date de publication :
1998-08-24
Code(s) de l'ICS :
33.180.01
End-face image analysis procedure for the calibration of optical fibre geometry test sets
Describes the calibration of test sets which perform end-face image analysis. This is also known as near-field or grey-scale analysis. The principles may also be applied to test sets of a different type. This standard addresses the calibration of measurements made on single-mode fibres only. This type of test set may also be used to measure multimode fibres, but the evaluation of uncertainties…
Éditeur :
IEC
Statut :
Révisé
Date de publication :
1998-08-24
Code(s) de l'ICS :
33.180.01
Procédure d'analyse d'image d'extrémité pour l'étalonnage de dispositifs d'...
Describes the calibration of test sets which perform end-face image analysis. This is also known as near-field or grey-scale analysis. The principles may also be applied to test sets of a different type. This standard addresses the calibration of measurements made on single-mode fibres only. This type of test set may also be used to measure multimode fibres, but the evaluation of uncertainties…
Éditeur :
IEC
Statut :
Révisé
Date de publication :
1998-08-24
Code(s) de l'ICS :
33.180.01

Spacer