This document covers the safety requirements for aero derivative and industrial gas turbine prime mover applications using liquid or gaseous fuels and the safety related control and detection systems and essential auxiliaries for all types of open cycles (simple, combined, regenerative, reheat, etc.) used in onshore and offshore applications including floating production platforms.
This document…
Assistive products — General requirements and test methods
This document specifies general requirements and test methods for assistive products, considered to be medical devices, intended for use to alleviate or compensate for a disability.
This document does not apply to assistive products which achieve their intended purpose by administering pharmaceutical substances to the user.
NOTE 1 Assistive products are considered to be medical devices in some…
1 Scope
1.1 This standard applies to the following types of transfer switches that have a maximum rating of 1000
volts for use in non-hazardous locations, in accordance with Annex A1, Item 1:
a) Automatic transfer switches;
b) Manual or non-automatic transfer switches;
c) Closed transition transfer switches;
d) Hybrid transfer switches;
e) Transfer switches for fire pumps;
f) Bypass/…
Household and similar electrical appliances — Safety — Part 2-24: Particular requirements for refrig...
1 Scope
This clause of Part 1 is replaced by the following:
This International Standard deals with the safety of the following appliances, their RATED VOLTAGE being not
more than 250 V for single-phase appliances, 480 V for other appliances and 24 V DC for appliances
when battery operated:
– REFRIGERATING APPLIANCES for household and similar use;
– ICE-MAKERS incorporating a motor-…
1 Scope
1.1 General
This Standard specifies requirements for the identification of hazards, and assessment and control of risks, across first responder occupations. This Standard can be applied to any type of risk and can be applied to both sleep-related and task-related fatigue.
It is intended that this Standard be utilized to harmonize risk management processes in existing and future…
1 Scope
1.1 Application
This Standard provides minimum requirements for oil-burning equipment, including
a)
fuel oil filters;
b)
draft regulators;
c)
flue pipe mounted heat reclaimers;
d)
through-the-wall venting systems;
e)
systems that supply outside combustion air; and
f)
used-oil-burning equipment.
1.2 Intended use
This Standard is to be used in conjunction with the other…
1 Scope
1.1 Application
This Standard applies to
a) oil burners of the atomizing type (irrespective of size, firing rate, or grade* of fuel oil) that are
designed primarily for installation in warm-air, hot-water, and steam-heating equipment;
* The grade of fuel oil should be as specified in CSA B140.0, except for grade B6-B20, which is specified in
ASTM D396.
b) atomizing-type oil burners…
1 Scope
1.1 Application
This Standard applies to complete, vent- (flue-) connected, or direct vent connected oil-fired warm air furnaces and unit heaters, irrespective of the heating capacity or the type of burner used. This Standard also applies to oil-fired condensing warm air furnaces.
1.2 Intent
This Standard applies to furnaces employing forced circulation of the heated air and furnaces…
1 Scope
1.1 Inclusions
This Standard specifies design and performance requirements for floor drains, adjustable floor drains, and area drains that are used inside of, or adjacent to, building structures. Drains of outlet NPS-2 and smaller, intended only for installation in shower areas, are covered in this Standard and in ASME A112.18.2/CSA B125.2 as well.
1.2 Exclusions
This Standard does…
1 Scope
1.1 Inclusions
This Standard specifies design and performance requirements for roof drains. This Standard applies to the following types of roof drains:
a)
general purpose;
b)
gutter and cornice;
c)
parapet and promenade;
d)
balcony; and
e)
deck.
1.2 Exclusions
This standard does not apply to siphonic roof drains covered under ASME A112.6.9/CSA B79.9.
1.3 Illustrations…
