Steel roller chains, types S and C, attachments and sprockets
This International Standard specifies the characteristics of a range of steel roller chains, dimensionally derived from the malleable iron type and suitable for the conditions of operation and maintenance prevailing in such fields as agriculture, building, quarrying and related industry, mechanical handling, etc., and of associated chain sprockets.
Pressure Relief Devices for Natural Gas Vehicle (NGV) Fuel Containers
This is a searchable PDF.
1. INTRODUCTION
1.1 General. This standard has been developed to identify performance requirements for pressure relief devices for Natural Gas Vehicle (NGV) fuel containers. This standard sets minimum requirements for pressure relief devices produced for use on NGV fuel containers. NGV fuel containers comply with ANSI/IAS NGV2, Basic Requirements for Compressed…
Oil of turpentine, Iberian type (Pinus pinaster Sol.)
This International Standard specifies certain characteristics of oil of turpentine, Iberian type (Pinus pinaster Sol.), in order to facilitate assessment of its quality.
Insulation co-ordination - Part 2: Application guide
1 General
1.1 Scope
This part of IEC 71 constitutes an application guide and deals with the
selection of insulation levels of equipment or installations for three-phase
electrical systems. Its aim is to give guidance for the determination of the
rated withstand voltages for ranges I and II of IEC 71-1 and to justify the
association of these rated values with the standardized highest…
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 218: ...
Gives the requirements for one type of heat-shrinkable polyolefin sleeving with a temperature index of 135 and a nominal shrink ratio of 3:1. This sleeving is not flame retarded. It is normally supplied with internal diameter up to 39 mm and the standard colour is transparent.
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 218:...
Donne les prescriptions relatives à un type de gaines thermorétractables en polyoléfine dont l'indice de température est de 135 et ayant un rapport de rétreint nominal de 3:1. Cette gaine n'est pas retardée à la flamme. Il est normalement fournie avec un diamètre intérieur allant jusqu'à 39 mm et la couleur standard est transparente.
Flexible insulating sleeving - Part 3: Specifications for indiviual types of sleeving - Sheet 272: H...
Gives the requirements for one type of heat-shrinkable, flame retarded, fluid resistant, elastomer sleeving with temperature index of 120 and a nominal shrink ratio of 2:1. This sleeving is normally supplied with internal diameter up to 51 mm and the standard colour is black.
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 272:...
Donne les prescriptions relatives à un type de gaines thermorétractables en élastomère, retardée à la flamme et résistant aux fluides, dont l'indice de température est de 120 et ayant un rapport de rétreint nominal de 2:1. Cette gaine est normalement fournie avec un diamètre intérieur allant jusqu'à 51 mm et la couleur standard est noire.
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 233: ...
Gives the requirements for one type of heat-shrinkable, flame retarded, fluid resistant, fluoroelastomer sleeving with temperature index of 200 and a nominal shrink ratio of 2:1. This sleeving is normally supplied with internal diameter up to 51 mm and the standard colour is black.
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 233:...
Donne les prescriptions relatives à un type de gaines thermorétractables en fluoroélastomère, retardée à la flamme et résistant aux fluides, dont l'indice de température est de 200 et ayant un rapport de rétreint nominal de 2:1. Cette gaine est normalement fournie avec un diamètre intérieur allant jusqu'à 51 mm et la couleur standard est noire.
