Information technology - Message Handling Systems (MHS): Message store: Abstract service definition ...
This Recommendation | International Standard defines the Message Store abstract-service. This abstract-service is
provided by the Message Store access protocol (specified in ITU-T Rec. X.419 | ISO/IEC 10021-6) in conjunction with
the MTS abstract-service (defined in ITU-T Rec. X.411 | ISO/IEC 10021-4), together with the Remote Operations
Service Element (ROSE) services (defined in ITU-T Rec. X.…
Information technology - Message Handling Systems (MHS): Electronic Data Interchange Messaging Syste...
This Recommendation | International Standard is one of a series on message handling. The entire set provides a
comprehensive blueprint for a Message Handling System (MHS) realized by any number of cooperating open systems.
The purpose of an MHS is to enable users to exchange messages on a store-and-forward basis. A message submitted on
behalf of one user, the originator, is conveyed by the…
Information technology - Message Handling Systems (MHS): MHS Routing - Guide for messaging systems m...
This Recommendation | Technical Report specifies the means by which the administrator of various aspects of an MHS
system may configure information into the directory for MTAs to use to determine the routing of messages.
ITU-T Rec. X.412 | ISO/IEC 10021-10 provides a set of directory structures that may be configured in many different
ways to support a particular MHS routing strategy. In order to…
Epoxy-coated steel for the reinforcement of concrete
This International Standard specifies requirements for fusion-bonded epoxy-coated post-fabricated and prefabricated
steel bar, wire and welded fabric for the reinforcement of concrete.
This International Standard permits the application of either flexible (type A) or nonflexible (type B) coatings. Steel
reinforcing bar, wire and welded fabric coated with a nonflexible (type B) coating shall not…
Aerospace — UNJ threads — General requirements and limit dimensions
This International Standard specifies the general requirements and limit dimensions of inch series UNJ threads with
controlled root radius for aerospace construction.
It determines the basic triangular profile for this type of thread and gives a system for designating the diameter and
number of threads per inch combinations. For all diameters 0,060 in (1,524 mm) to 6,000 in (152,4 mm), it offers…
1. Scope
1.1
This Standard specifies energy performance requirements for self-contained drinking-water coolers having an hourly rated capacity of up to 20 mL/s (20 Us gal/h). Included are
(a) uniform procedures for measuring capacity and energy consumption; and
(b) maximum energy consumption levels.
1.2
This Standard applies to the following mechanical, thermoelectric, and other…
Information technology — Synchronous Split Transfer Type System Bus (STbus) — Logical Layer
This International Standard specifies the logical specifications of STbus which is a highperformance and highly reliable system bus. STbus adopts a synchronous transfer method with a high-speed clock and a split transfer method enabling to minimize bus holding time during one bus operation and to use a bus efficiently.
The contents given in this specifications are as follows:
a) System bus…
Describes the measurement of screening attenuation by the reverberation, or stirred, chamber, suitable for virtually any type of microwave component and having no theoretical upper frequency limit. It is only limited toward low frequencies due to the size of the test equipment, which is frequency dependent and is only one of several methods of measuring sreening attenuation. For the purpose of…
1. Scope
1.1
This Standard outlines requirements and classifications for automatic and
manual descent control devices intended for use in the workplace. These
devices are not used for fall arrest. Appropriate fall protection equipment is
also required in the presence of a fall hazard, except in the case of emergency
egress.
1.2
This Standard applies to equipment intended to be used…
1. SCOPE
1.1 This standard applies to a flat latex paint for most interior walls and
ceilings, with the exception of bathrooms and kitchens, either new or
previously painted.
1.2 The paint is suitable for application over all types of wall surfaces,
including wallboard, gypsum board, dry plaster, cement, brick or concrete
block.
1.3 The testing and evaluation of a product…