Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 211: ...
Gives the requirements for semi-rigid, heat-shrinkable polyolefin sleeving with a nominal shrink ratio of 2:1 that has been found suitable for temperatures up to 135 °C.
Type 1: General purpose, flame-retarded, opaque colours.
Type 2: General purpose, non flame-retarded, translucent.
Type 3: Fluid resistant, flame-retarded, opaque colours.
Type 4: Fluid resistant, non flame-retarded,…
This International Standard specifies a method for the determination of castor oil seed (Ricinus communis) husks in
single and compound animal feeding stuffs and, in particular, in oilseed residues.
The limits of detection is 5 mg/kg.
The method requires final microscopical identification of the isolated husks. This last phase therefore requires a
specialist who has had sufficient experience in…
Road construction and maintenance equipment — Chippings spreaders — Terminology and commercial speci...
This International Standard establishes the terminology and determines the type of technical and commercial
specifications for chippings spreaders.
This International Standard is applicable to chippings spreaders intended for road construction and surface coating.
Rubber seals — Joint rings for water supply, drainage and sewerage pipelines — Specification for mat...
This International Standard specifies requirements for materials used in vulcanized rubber seals for
cold drinking-water supplies (up to 50 °C); drainage, sewerage and rainwater systems (continuous flow up to 45 °C and intermittent flow up to 95 °C).
The different designations of seals specified are defined according to their type, application and requirements.
General requirements for finished…
Oil of cedarwood, Chinese type (Cupressus funebris Endlicher)
This International Standard specifies certain characteristics of the oil of cedarwood, Chinese type ( Cupressus funebris Endlicher), in order to facilitate assessment of its quality.
Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindri...
This International Standard specifies two methods for the determination of the resistance of rubber to abrasion by means of a rotating cylindrical drum device.
The methods involve determination of the volume loss due to the abrasive action of rubbing a test piece over a specified grade of abrasive sheet. Method A is for a non-rotating test piece and method B for a rotating test piece. For each…
Personal fall-arrest systems — Part 4: Vertical rails and vertical lifelines incorporating a sliding...
This part of ISO 10333 specifies requirements, test methods, instructions for use and maintenance, marking, labelling and packaging, as appropriate, for vertical rails and vertical lifelines which incorporate a sliding-type fall arrester.
When connected to a full-body harness as specified in ISO 10333-1, vertical rails and vertical lifelines which incorporate a sliding-type fall arrester…
Conveyor belts — Determination of strength of mechanical fastenings — Static test method
This European Standard specifies a static test method for measuring the strength of a conveyor belt mechanical fastening; the mechanical joints can be either of the type employing a connecting rod or of a type which does not employ a connecting rod.
This standard does not cover vulcanized joints.
NOTE The purpose of the test specified in this standard is to eliminate mechanical fastenings of…
Gas Clothes Dryers - Volume 1 - Type 1 Clothes Dryers
1.1 Scope
1.1.1 This standard applies to newly produced Type 1 clothes dryers (see Part
IV, Definitions), hereinafter referred to as dryers, constructed entirely of
new, unused parts and materials:
a. For use with natural gas;
b. For use with manufactured gas;
c. For use with mixed gas;
d. For use with propane gas;
e. For use with liquefied petroleum gases;
f. For use with LP gas-…
ISO 492 specifies tolerances for boundary dimensions (except chamfer dimensions) and the running accuracy of radial rolling bearings specified in ISO 15, ISO 355 and ISO 8443.
This International Standard does not apply to certain radial bearings of particular types (e.g., drawn cup needle roller bearings) or for particular fields of application (e.g., airframe bearings and instrument precision…
