Rechercher

1. Scope 1.1 General This standard contains requirements for the material, design, manufacture and testing of serially produced, refillable Type NGV 2 containers intended only for the storage of compressed natural gas for vehicle operation. These containers are to be permanently attached to the vehicle. Type NGV 2 containers shall not be over 1000 liters (35.4 ft3) water capacity. Where the…

This National Standard of Canada is equivalent to International Standard ISO 19904-1:2006. 1 Scope This part of ISO 19904 provides requirements and guidance for the structural design and/or assessment of floating offshore platforms used by the petroleum and natural gas industries to support the following functions: - production; - storage and/or offloading; - drilling and production; -…

This National Standard of Canada is joint with UL 60745-2-5; and both are based on International Standard IEC 60745-2-5. 1 Scope This clause of Part 1 is applicable, except as follows: Addition: This standard applies to all types of circular saws. Circular saws hereinafter will be referred to as saws. This standard does not apply to saws used with abrasive wheels.

B64.0-07 1 Scope 1.1 The CSA B64 Series of Standards covers vacuum breakers and backflow preventers that are used in potable water supply systems to prevent cross-connections. 1.2 This Standard specifies definitions, general requirements, test methods, markings, and instructions that are common to some or all of the CSA B64 Series. 1.3 This Standard is not a complete Standard in…

1. SCOPE 1.1 This standard applies to three types of distillate fuel oils that are suitable for use in liquid-fuel-burning equipment without preheating, and three types of fuel oils that contain residual fuel components and require preheating. 1.2 The heating fuel oils covered by this standard are intended for use in oil-burning equipment for the generation of heat for domestic and…

1. SCOPE 1.1 This standard applies to two types of light petroleum distillates. 1.2 The light petroleum distillates covered by this standard are intended for use in applications as described below. 1.2.1 Type No. 1-K Kerosene is intended for use in unvented space heaters as described in CAN/CSA-B140.9.3, when used in well-ventilated surroundings, and in wick-fed illuminating lamps. 1.2.2 Type…

1. SCOPE 1.1 This standard applies to four types of automotive (on-road) diesel fuel, Type A-LS, Type A-ULS, Type B-LS and Type B-ULS, suitable for use in high-speed diesel engines that require low-sulphur diesel fuel to meet emission control regulations. 1.2 All types of this fuel can be used in all high-speed diesel-powered equipment. 1.2.1 Types A-LS and A-ULS are intended for use in…

1. SCOPE 1.1 This standard defines equipment requirements, performance criteria, and operating and testing procedures for the implementation of a vapour control system (VCS) in gasoline distribution networks including terminals, bulk plants, service stations and cargo tanks, commonly known as Stage I. (See Figure 1 for a schematic representation.) 1.1.1 This standard does not include vapour…

IEC 60191-6-13:2007 gives a design guideline of open-top-type semiconductor sockets for Fine-pitch Ball Grid Array ("FBGA" hereafter) and Fine-pitch Land Grid Array ("FLGA" hereafter). This standard is intended to establish the outline drawings and dimensions of the open-top-type socket out of the test and burn-in sockets applied to FBGA and FLGA.

IEC 61097-1:2007 specifies the performance standards and type testing of marine radar transponders used in search and rescue operations at sea (SART), as required by Regulation 6.2.2 of Chapter III, and 7.1.3 and 8.3.1 of Chapter IV of the 1988 amendments to the 1974 International Convention for Safety of Life at Sea (SOLAS), and which is associated with IEC 60936 (Shipborne radar) and IEC 60945…