Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test m...
IEC 60695-2-11:2014 specifies a test method on an end product. It is intended to simulate the effects of thermal stresses produced by an electrically heated source to represent a fire hazard. This test method is used to check that, under defined test conditions, an end product exposed to an electrically heated source has either a limited ability to ignite or, if it ignites, a limited ability to…
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test m...
IEC 60695-2-11:2014 RLV contains both the official IEC International Standard and its Redline version. The Redline version is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition.
IEC 60695-2-11:2014 specifies a test method on an end product. It is intended to simulate the effects of thermal…
Optical fibres - Part 1-51: Measurement methods and test procedures - Dry heat (steady state) tests
IEC 60793-1-51:2014 provides a practical method for evaluating fibre performance in a defined environment. The purpose of this standard is to determine the suitability of optical fibre sub-category A1a to A1d multimode fibres and class B and C single-mode fibres to withstand the environmental condition of high temperature (dry heat) which may occur in actual use, storage and/or transport. The…
Optical fibres - Part 1-52: Measurement methods and test procedures - Change of temperature tests
IEC 60793-1-52:2014 provides a practical method for evaluating fibre performance in a defined environment. The purpose of this standard is to define a test that determines the suitability of sub-category A1a to A1d multimode fibres and class B and C single-mode fibres to withstand the environmental condition of change in temperature which may occur in actual use, storage and/or transport. The…
Optical fibres - Part 1-53: Measurement methods and test procedures - Water immersion tests
IEC 60793-1-53:2014 provides a practical method for evaluating fibre performance in a defined environment. The purpose of this standard is to define a test that determines the suitability of sub-category A1a to A1d multimode fibres and class B and C single-mode fibres to withstand the environmental condition of immersion in distilled or demineralized water which may occur in actual use, storage…
Filler metals and allied materials for metal arc welding
Scope
1.1
This Standard specifies requirements for the classification and certification of
a) carbon steel covered electrodes for shielded metal arc welding (SMAW);
b) chromium and chromium-nickel steel covered electrodes for SMAW, including electrodes designated for welding heat-resistant steels containing more than 11% chromium and less than 50% nickel;
c) low alloy steel covered…
1 Scope
1.1 These requirements cover electrically operated single and multiple station smoke alarms intended for open area protection in indoor locations, in accordance:
a) Installation of Smoke Alarms, CAN/ULC-S553;
b) National Building Code of Canada; and
c) National Fire Code of Canada.
1.2 A single station smoke alarm (e.g. ionization-type, photoelectric-type, smoke alarm with…
1 Domaine d’application
1.1 Les présentes exigences se rapportent aux avertisseurs de fumée électriques dans une configuration
à poste simple ou à postes multiples destinés à assurer la protection des aires ouvertes dans les
emplacements intérieurs, conformément aux publications suivantes :
a) Installation des avertisseurs de fumée, CAN/ULC-S553;
b) Code national du bâtiment du Canada; et…
Scope
1.1
This Standard specifies the requirements for cord sets and power-supply cords employing molded-on or assembled-on fittings, rated 600 V maximum, and intended for use in non-hazardous locations in accordance with the Canadian Electrical Code, Part I, CSA C22.1-12 and General Requirements-Canadian Electrical Code, Part II, CSA C22.2 No. 0-10.
1.2
This Standard also specifies the…
Anaesthetic and respiratory equipment — Tracheal tubesand connectors
Scope
This International Standard provides essential performance and safety requirements for oro-tracheal and
naso-tracheal tubes and tracheal tube connectors. Tracheal tubes with walls reinforced with metal or
nylon, tracheal tubes with shoulders, tapered tracheal tubes, tracheal tubes with means for suctioning
or monitoring or delivery of drugs or other gases, and the many other types of…
