Software and systems engineering — Tools and methods for product line technical management
ISO/IEC 26555:2015 deals with the tools and methods of technical management for software products, software services, software-intensive systems (including System Architecture and excluding hardware) within a product line. The scope of this International Standard is as follows:
? Enable the users of this standard to holistically understand, adopt, and enact the processes, tools, and methods for…
Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode...
IEC 60793-2-50:2015 is applicable to optical fibre categories B1.1, B1.2, B1.3, B2, B4, B5 and B6. A map illustrating the connection of IEC designations to ITU-T designations is shown in Annex I. These fibres are used or can be incorporated in information transmission equipment and optical fibre cables. Three types of requirements apply to these fibres:
- general requirements, as defined in IEC…
Software and systems engineering - Tools and methods for product line technical management
ISO/IEC 26555:2015 deals with the tools and methods of technical management for software products, software services, software-intensive systems (including System Architecture and excluding hardware) within a product line. The scope of this International Standard is as follows:
? Enable the users of this standard to holistically understand, adopt, and enact the processes, tools, and methods for…
Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimo...
IEC 60793-2-10:2015 is applicable to optical fibre types A1a, A1b, and A1d. These fibres are used or can be incorporated in information transmission equipment and optical fibre cables. Type A1a applies to 50/125 μm graded index fibre. Three bandwidth grades are defined as A1a.1, A1a.2 and A1a.3. Each of these bandwidth grades is defined for two levels of macrobend loss performance that are…
Optical fibres - Part 2-20: Product specifications - Sectional specification for category A2 multimo...
IEC 60793-2-20:2015 is applicable to sub-categories A2a, A2b, and A2c. These fibres are used or can be incorporated in information transmission equipment and optical fibre cables (typically up to 2 km). Three types of requirements apply to these fibres:
- general requirements as defined in IEC 60793-2;
- specific requirements common to the category A2 multimodal fibres covered in this standard…
Gas cylinders — Composite construction — Periodic inspection and testing
ISO 11623:2015 specifies the requirements for periodic inspection and testing and to verify the integrity for further service of hoop-wrapped and fully-wrapped composite transportable gas cylinders, with aluminium-alloy, steel or non-metallic liners or of linerless construction (Types 2, 3, 4, and 5), intended for compressed, liquefied or dissolved gases under pressure, of water capacity from 0,5…
Cosmetics — Microbiology — Detection of Pseudomonas aeruginosa
ISO 22717:2015 gives general guidelines for the detection and identification of the specified microorganism Pseudomonas aeruginosa in cosmetic products. Microorganisms considered as specified in this International Standard might differ from country to country according to national practices or regulations.
In order to ensure product quality and safety for consumers, it is advisable to perform an…
Acoustics — Field measurement of sound insulation in buildings and of building elements — Part 2: Im...
ISO 16283-2:20015 specifies procedures to determine the impact sound insulation using sound pressure measurements with an impact source operating on a floor or stairs in a building. These procedures are intended for room volumes in the range from 10 m3 to 250 m3 in the frequency range from 50 Hz to 5 000 Hz. The test results can be used to quantify, assess and compare the impact sound insulation…
Intelligent transport systems — Framework for cooperative telematics applications for regulated comm...
ISO/TS 15638-13:2015 addresses the provision of ?Mass (4.37) information for jurisdictional control and enforcement' and specifies the form and content of such data required to support such systems and access methods (4.3) to that data.
The Scope of this part of ISO 15638 is to provide specifications (4.50) for common communications and data exchange aspects of the application service (4.6)…
Information technology — ASN.1 encoding rules — Part 7: Specification of Octet Encoding Rules (OER)
ISO/IEC 8825-7:2015 specifies a set of Basic Octet Encoding Rules (BASIC-OER) that may be used to derive a transfer syntax for values of the types defined in Rec. ITU-T X.680 | ISO/IEC 8824-1, Rec. ITU‑T X.681 | ISO/IEC 8824-2, Rec. ITU-T X.682 | ISO/IEC 8824-3, Rec. ITU-T X.683 | ISO/IEC 8824-4. This Recommendation | International Standard also specifies a set of Canonical Octet Encoding Rules (…
