Information technology - Open systems interconnection - Part 6: The Directory: Selected attribute ty...
This document defines a number of attribute types and matching rules which may be found useful across a range of applications of the Directory.
Attribute types and matching rules fall into three categories, as described below.
Some attribute types and matching rules are used by a wide variety of applications or are understood and/or used by the Directory itself.
NOTE 1 ? It is recommended that an…
Information technology - Open systems interconnection - Part 7: The Directory: Selected object class...
This document defines a number of object classes and name forms which may be found useful across a range of applications of the Directory. The definition of an object class involves listing a number of attribute types which are relevant to objects of that class. The definition of a name form involves naming the object class to which it applies and listing the attributes to be used in forming…
Information technology - Open systems interconnection - Part 8: The Directory: Public-key and attrib...
This document addresses some of the security requirements in the areas of authentication and other security services through the provision of a set of frameworks upon which full services can be based. Specifically, this Recommendation | International Standard defines frameworks for:
? public-key certificates; and
? attribute certificates.
The public-key certificate framework defined in…
Organic production systemsPermitted Substances Lists
1 Scope
1.1 This National Standard of Canada1 provides additional information to CAN/CGSB-32.310, Organic production
systems — General principles and management standards, in the form of permitted substances to be used as
annotated in accordance with the scope of the table in which they are listed. Use of a listed substance in a manner
inconsistent with the scope of the table in which it…
1 Scope
1.1 This standard applies to suit systems to be worn by helicopter passengers during transportation over water
where thermal protection may be required.
1.2 The primary function of a suit system meeting this standard is to provide the helicopter passenger protection
from the effects of cold water during the initial hours of immersion.
1.3 Helicopter passenger transportation suit…
Performance Requirements for Chemical Dispensers with Integral Backflow Protection
1.2 Scope
1.2.1 Description
This standard applies to those devices classified as chemical dispensing systems and shall
be protected by an air gap complying to ASME A112.1.3-2000 (R2015), an integral elastomer
gap, or an Atmospheric Vacuum Breaker (AVB). If an AVB is used as its method of backflow
protection, it must conform with ASSE 1001 or CSA B64.1.1.
1.2.2 Pressure Range
Devices…
Test method for measuring efficiency and pressure loss of drain water heat recovery units
1 Scope
1.1
This Standard specifies requirements for measuring the heat recovery efficiency and pressure loss for drain water heat recovery (DWHR) units.
1.2
This Standard applies to DWHR units
a)
of any size; and
b)
with a configuration where potable water and drain water flow rate is equal;
1.3
In this Standard, “shall” is used to express a requirement, i.e., a provision that the user…
1 Scope
1.1
This Standard specifies requirements for the durability and safety of drain water heat recovery (DWHR) units.
1.2
This Standard applies to DWHR units of any diameter and length and configuration for use with potable water, and to their components and materials supplied by the manufacturer, their assembly and installation instructions, and their operation after assembly in…
Mechanical couplings for drain, waste, and vent pipe and sewer pipe
1 Scope
1.1
This Standard covers mechanical couplings that are used to axially join pipes and fittings in non-pressure drain, waste, and vent (DWV) piping systems and sewer piping systems located inside or outside buildings and above ground or underground.
Notes:
1)
Caution should be exercised when installing mechanical couplings at low temperatures. The coupling manufacturer should be…
1 Scope
1.1
This Standard provides requirements for grade-level, in-ground enclosures. The enclosures are made of polymer concrete, composite, or plastic (enclosure covers may be made of metal), intended for conductors and connections at voltages 750 V or less.
1.2
These enclosures are not intended to be installed where vehicular traffic normally occurs.
1.3
These enclosures are intended to…