Road vehicles — Vehicle to grid communication interface — Part 21: Common 2nd generation network lay...
The document specifies all common test cases to be applied to and correctly handled by EVs (EVCC) and EVSEs (SECC) implementing ISO 15118-20 that are independent of a particular charging type (AC, DC, ACD, WPT charging). The document considers the use cases defined in ISO 15118-1:2019
The test system will comprise:
- A simulated SECC to verify the correct behaviour of a real EVCC
- A simulated…
Ergonomics of the thermal environment — Evaluation of thermal environments in vehicles — Part 2: Det...
ISO 14505-2:2006 provides guidelines for the assessment of the thermal conditions inside a vehicle compartment. It can also be applied to other confined spaces with asymmetric climatic conditions. It is primarily intended for assessment of thermal conditions, when deviations from thermal neutrality are relatively small. Appropriate methodology as given in ISO 14505-2:2006 can be chosen for…
Robotics — Performance criteria and related test methods for service robots — Part 6: Lower-limb wea...
This International Standard specifies the test method to evaluate the assistance/enhancement performance of the lower-limb wearable robots by using an anthropomorphic test dummy robot (ATDR). ATDR wears the lower-limb wearable robot and runs test instead of a human thereby ensuring the objectivity and repeatability of the test. This International Standard is applied to all wearable robots that…
ISO 3170:2004 specifies the manual methods to be used for obtaining samples of liquid or semi-liquid hydrocarbons, tank residues and deposits from fixed tanks, railcars, road vehicles, ships and barges, drums and cans, or from liquids being pumped in pipelines.
ISO 3170:2004 applies to the sampling of petroleum products, crude oils and intermediate products, which are stored in tanks at or near…
Phase quantitative analysis of residual quartz in silica bricks — X-ray diffraction method
This standard specifies the principle of phase quantitative analysis of residual α-quartz in silica bricks by X-ray diffraction, apparatus, reference materials, sample preparation, standard curve establishment, test procedures, results and calculations, and test report.
This standard applies to the phase quantitative analysis of residual α-quartz in silica bricks, and the phase quantitative…
Refrigerating systems and heat pumps — Safety and environmental requirements — Part 1: Definitions, ...
ISO 5149-1:2014 specifies the requirements for the safety of persons and property, provides guidance for the protection of the environment, and establishes procedures for the operation, maintenance, and repair of refrigerating systems and the recovery of refrigerants.
ISO 5149-1:2014 specifies the classification and selection criteria applicable to the refrigerating systems and heat pumps. These…
Road vehicles — Box task and detection response task to measure visual-manual and cognitive demand
This document defines key terms and parameters applied in the analysis of cognitive and visual-manual workload induced by transport information and control systems (TICS). It provides guidelines and minimum requirements on equipment and procedures for analysing cognitive and visual-manual load including assessment of TICS to:
— plan evaluation trials;
— specify (and install) data capture…
Guidance for the analysis of differences between various standards of fibre reinforced plastic-worki...
This document sets out test methods for fibre-reinforced plastic working towers made of
prefabricated elements.
This document only encompasses fibre reinforced plastic working towers made of prefabricated
elements，It can be designed with reference to EN 1004-1.
This document does not apply to working towers made of materials other than fibre-reinforced
plastic. This document does not apply to…
Earth-moving machinery — Operator's manual — Part 2: List of references
This document provides a list of standard deliverables, containing provisions for information to be included in the operator’s manual.
This document applies to earth-moving machinery as defined in ISO 6165.
The list of standard deliverables is being provided as guidance in creating operator´s manuals.
NOTE Standard deliverables refer to different types of documents, e.g. International…
Industrial systems, installations and equipment and industrial products — Structuring principles and...
This part of 81346 International Standard, published jointly by IEC and ISO, provides, in combination with
IEC 81346-1 and IEC 81346-2, rules and recommendations on the structuring of processes and basic
activities. It provides the tools to handle the information on processes in the area of technical products
and equipment.
It also provides classification of basic activities to enable a model of…
